679450
9
Zoom out
Zoom in
Previous page
1/37
Next page
9 GB/IE
Before use / Operation / Maintenance and Cleaning
Before use
Always pull the mains plug before executing
settings on the device.
Mounting the agitator (see Ill. A)
Firmly screw the shaft
7 b
to the mixing spi
ral
7 a
.
Subsequently, screw the agitator
7
into the
agitator shaft with the M-14 inner threading
4
.
Secure the chuck with an open-end spanner
2
and tighten the stirrer
7
with a second open-
end spanner
2
.
Dismantling the agitator
To remove the agitator, repeat the process in
the reverse order.
Installing the support bracket
Install the support bracket
3
by securing the
four included crosshead screws in the desig-
nated location on the handle (see Fig. C).
Using the support bracket
Use the support bracket
3
to hang the device
or to set it on the ground. This will prevent it
from dirtying.
Operation
Turning the device ON / OFF
(see Ill. B)
Switching on:
Press the ON / OFF switch
5
.
Switching off:
Release the ON / OFF switch
5
.
Switching on permanent operation:
Secure ON / OFF switch
5
with hold-to-
run
button
6
.
Switching off permanent operation:
Press ON / OFF switch
5
quickly.
Setting the speed (see Ill. B)
Note: The ON / OFF switch
5
has a variable
speed control.
Note: The speed cannot be adjusted in non-stop
operation.
Press the ON / OFF switch
5
lighlty to reduce
the speed.
Increase the pressure to increase the speed.
Working with the mixer
Submerge the mixer in the mixture at a low
speed.
After the agitator has been submerged com-
pletely, you may increase the speed.
During the mixing process, move the agitator
around the mixing vessel and mix the mixture
until it is completely processed.
Maintenance and Cleaning
DANGER OF INJURY! Pull
the mains plug out of the mains socket before you
carry out any task on the device.
Cleaning
Use a dry cloth to clean the casing. Under no
circumstances should you use petrol, solvents
or cleaning agents, which may be aggressive
to the plastic.
Always keep the device clean, dry and free of
oil or grease. Do not allow liquids to enter the
interior of the paint and mortar mixer.
Clean the paint and mortar mixer regularly,
preferably immediately after finishing your work.
General power tool safety warnings / Safety notes for paint and mortar mixer
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PFMR 1400 C2 - IAN 273041 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PFMR 1400 C2 - IAN 273041 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info