679265

Parkside PFBS 12 B2 - IAN 305279 Manual

13
Zoom out
Zoom in
Previous page
1/36
Next page
PFBS 12 B2
■ 10 
│
 GB
│
IE
│
NI
Charging the integrated battery
NOTE
► A new battery or a battery which has not
been used for a long time will need to be
charged before first use/reuse. It will reach its
full capacity after 3–5 charge cycles.
The charging process lasts around 180
minutes.
Starting charging:
♦ Connect the charger
to the charging socket
on the appliance.
♦ Connect the charger
to a mains power
socket.
The battery is fully charged when the battery
LED
shows RED/ORANGE/GREEN.
Stopping charging:
♦ Disconnect the charger
from the mains
power supply.
♦ Disconnect the charger
from the charging
socket
on the appliance.
CAUTION!
► Never recharge a battery again immediately
after charging. There is a risk that the battery
will become overcharged.
Checking the battery charge level
If the appliance is switched on, the remaining
charge will be shown on the battery LED
as
follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Changing/inserting the tool/collet
chuck
♦ Press the spindle lock and hold it down.
♦ Turn the tensioning nut
until the lock clicks
into place.
♦ Undo the tensioning nut
from the thread
using the combination spanner
.
♦ Remove any attached tool.
♦ First push the intended tool through the tensioning
nut
before inserting it into the appropriate
collet chuck
for the tool shaft.
♦ Press the spindle lock
and hold it down.
♦ Push the collet chuck
into the thread insert
and screw the tensioning nut
tight with the
combination spanner
.
NOTE
► Use the screwdriver side of the combination
spanner
to undo and tighten the screw on
the mandrel .
Switching on and off/setting speed
range
Switching on/setting the speed range:
♦ Set the On/Off switch
to the position "I".
♦ Set the speed control
to a position between
"1" and "MAX".
Switching off:
♦ Set the On/Off switch
to the position "O".
Notes on working with materials/
tools/speed range
■ Use the milling bits for working on steel and
iron at maximum speed.
■ Determine the rotational speed range for working
on zinc, zinc alloys, aluminium and copper by
trying it out on test pieces.
■ Use a low rotational speed for work on plastics
and materials with a low melting point.
■ Use a high rotational speed for working on
wood.
■ Carry out cleaning, polishing and buffing work
in the medium speed range.
The following are recommendations only and not
binding. When carrying out practical work, carry
out your own tests to see which tool and which
settings are ideal for the material you are working
on.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PFBS 12 B2 - IAN 305279 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PFBS 12 B2 - IAN 305279 in the language / languages: English as an attachment in your email.

The manual is 0,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PFBS 12 B2 - IAN 305279

Parkside PFBS 12 B2 - IAN 305279 User Manual - German, Dutch, French - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info