595292

Parkside PEH 30 A1 - IAN 93528 Manual

31
Zoom out
Zoom in
Previous page
1/34
Next page
31 GB
Preparing for useGeneral safety advice for electrical power tools / Preparing for use
Q
The planing process
CAUTION! DANGER OF KICKBACK!
Always switch on the device before placing it
against the workpiece.
Set the required cutting depth.
Switch on the device.
Always place the front part of the sole
9
down
first on to the workpiece.
Guide the device with even forward movement
over the surface being planed.
Move the device forward at a slow rate and
ensure that the contact pressure acts evenly on
the sole
9
. Moving forward at too great a rate
results in a poorer surface quality and can lead
to blocking of the planing debris removal port.
Q
Chamfering edges (see Fig. H)
The V-grooves
10
in the front sole
9
allow the de
vice
to be used for simple chamfering of workpiece edges.
Use the V-groove most appropriate to your
desired chamfer width.
Place the planer with the V-groove
10
on the
work-
piece edge and guide the planer along the edge.
Q
Using the guide fence (see Fig. I)
Attach the guide fence
6
to the device with
the fixing screw
7
.
Release the fixing nut
8
and set the guide at
the desired distance.
Retighten the fixing nut
8
.
Exert some slight sideways pressure when guid-
ing the planer with the guide fence.
Q
Using the rebate depth stop
(see Fig. J)
Attach the rebate depth stop
12
to the device
with the fixing screw
11
.
Set the desired rebate depth with the rebate
depth stop
12
.
Make the required number of passes with the
planer until desired rebate depth is achieved.
Q
Removing and installing a
planer blade
20
(see Fig. D + E)
DANGER OF INJURY!
Before you carry out any work on the device always
pull the mains plug out of the mains socket.
CAUTION! The sharp cutting edges of the plan-
er blade
20
present an injury hazard! Never
touch the cutting edges of the planer blade
20
.
The planer blade
20
has two cutting edges and it
can be fitted either way around.
Replace the planer blade
20
when both cutting
edges are blunt.
Do not resharpen the planer blades
20
.
Reversing or replacing a planer blade
20
IMPORTANT INFORMATION:
Do not release the two Allen keys. They are used to
adjust the height of the blade shaft.
Adjustment is necessary only if you wish to use a
different planer blade type e.g. a profiled blade.
Always replace both blades at the same time to
avoid out of balance forces.
NOTE: If you only release one blade first then you
can use the factory-fitted second blade for orientation
when you fit the new blade.
1. Release the 3 bolts of the cutting element
18
using the supplied open spanner
26
.
Press the removable side guard
21
into the slot
in the housing.
2. Push the cutting element
18
sideways out from
the blade shaft
17
.
3. Push the planer blade
20
sideways out from
the cutting element
18
.
4. Reassembly is carried out in the reverse order
with a reversed or new planer blade.
5. Planer blades
20
can be obtained from the
service address indicated (see section about
warranty).
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PEH 30 A1 - IAN 93528 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PEH 30 A1 - IAN 93528 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PEH 30 A1 - IAN 93528

Parkside PEH 30 A1 - IAN 93528 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info