576694

Parkside PEH 30 A1 - IAN 102829 Manual

30
Zoom out
Zoom in
Previous page
1/34
Next page
30 GB
Preparing for use / Maintenance and cleaningPreparing for use
Switching off:
Release the ON / OFF switch
2
.
Note: For safety reasons the ON / OFF switch
2
cannot be locked in the ON position.
Q
Setting the cutting depth
The rotary control
13
can be used to set the cutting
depth in steps from 0–3.0 mm according to the cut-
ting depth scale
14
.
Q
Vacuum extraction of dust /
debris (see Fig. A)
DANGER OF INJURY!
Before you carry out any work on the device always
pull the mains plug out of the mains socket.
Planing debris removal port (right / left
selectable):
Release the planing debris removal port
3
by
turning it against the direction of the arrow (out
of the “Lock” position).
Pull the planing debris removal port
3
out of
the device.
The planing debris removal port
3
can be set
to face left or right in the planer.
Push the planing debris removal port
3
into
the device.
Lock the planing debris removal port
3
by
turning it into the “Lock” position.
External vacuum extraction:
If necessary fit the reducer piece
15
when using
a dust extraction system, e.g. a workshop dust
extraction system.
The vacuum cleaner / dust extraction device used
must be suitable for the material being planed.
Connection:
Place the reducer piece
15
firmly on to the
planing debris removal port
3
.
Push the hose of a suitable dust extraction device
approved for that purpose (e.g. a workshop
vacuum cleaner) on to the planing debris remov-
al port
3
or the reducer piece
15
.
Removal:
Pull the hose of the dust extraction device off
the planing debris removal port
3
or off the
reducer piece
15
.
Pull off the reducer piece
15
, if fitted.
Q
Parking shoe (see Figs. B / C)
The parking shoe
16
allows you to lay the device
down without the risk of damaging the workpiece.
When planing, the parking shoe
16
swings up and
exposes the rear part of the sole
9
.
Q
The planing process
CAUTION! DANGER OF KICKBACK!
Always switch on the device before placing it
against the workpiece.
Set the required cutting depth.
Switch on the device.
Always place the front part of the sole
9
down
first on to the workpiece.
Guide the device with even forward movement
over the surface being planed.
Move the device forward at a slow rate and
ensure that the contact pressure acts evenly on
the sole
9
. Moving forward at too great a rate
results in a poorer surface quality and can lead
to blocking of the planing debris removal port.
Q
Chamfering edges (see Fig. H)
The V-grooves
10
in the front sole
9
allow the de
vice
to be used for simple chamfering of workpiece edges.
Use the V-groove most appropriate to your
desired chamfer width.
Place the planer with the V-groove
10
on the
work-
piece edge and guide the planer along the edge.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PEH 30 A1 - IAN 102829 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PEH 30 A1 - IAN 102829 in the language / languages: English, German, French as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info