595303

Parkside PDT 40 D3 - IAN 109811 Manual

9
Zoom out
Zoom in
Previous page
1/53
Next page
9 GB/IE
Safety of the fastener driving tool / Preparing the product for use / Operation
Original accessories / tools
Use only the accessories and attachment
s
detailed in the operating instructions.
The use of fasteners or other accessories other
than those recommended in the operating in-
structions could lead to you suffering an injury.
Always have your air-powered tool
repaired by a professional using only
original spare parts. This will ensure the
air-powered tool remains safe.
Preparing the product for use
NOTE: always wear the protective goggles supplied
before putting the tool into operation. Remove the
protective film from the protective goggles before
using for the first time.
Connecting the compressed
air source
NOTE: The compressed air tacker must only be
operated with cleaned, oil-misted compressed air
and must not exceed the maximum operating pres-
sure of 8 bar. The compressor must be fitted with a
pressure reducer in order to regulate the operating
pressure.
Connect the device to a suitable compressed
air source.
1. To do so, press the compressed air hose quick-
release coupling (not included in the scope of
delivery) on the ¼
threaded nipple
4
of the
compressed air tacker.
Locking is automatic.
2. Connect the other end of the compressed air
hose to the (filter) pressure reducer on the com-
pressor.
Loading the magazine
1. Press the magazine lever
5
and pull the mag-
azine cover back to its stop position.
2. Insert the corresponding fastener (nails, see
Fig. B or staples, see Fig. C) into the magazine
6
. The tacks must be put on the rail of the ma-
gazine
6
.
3. Slide the magazine cover forwards until it locks.
Operation
Load the magazine
6
of the compressed air
tacker as described in the chapter “Loading the
magazine“.
Use the pressure reducer to set the correct
operating pressure.
Ensure that the permissible operating pressure
of 8 bar at the device is never exceeded.
Operating pressure that is too high does not
provide any performance increase, but only in-
creases compressed air consumption and ac-
celerates wear on the device.
Switch on the compressor.
Allow the compressor to run once long enough
until maximum tank pressure is reached and the
device is switched off.
Place the compressed air tacker on the workpiece
and press the trigger
2
.
NOTE: The compressed air tacker
is equipped with a trigger lock
9
.
The fastener will only
leave the device
when the mouth of the compressed air tacker is
pressed against the workpiece and the trigger
2
is actuated.
Check that the fastener has been driven in cor-
responding to the work requirements.
– If the fastener is protruding, increase the air
pressure in 0.5 bar increments.
– If the fastener is too deep, decrease the air
pressure in 0.5 bar increments.
As an alternative, you can accelerate the work
by keeping the trigger
2
depressed.
Set the compressed air tacker against the work-
piece.
Press the device against the workpiece until the
mouth
10
touches it. The fastener will leave the
device.
As long as the trigger
2
is kept depressed, each
time the mouth
10
touches the workpiece one
fastener will leave the device.
Safety of the fastener driving tool
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDT 40 D3 - IAN 109811 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDT 40 D3 - IAN 109811 in the language / languages: English, German, Dutch, French, Swedish, Finnish as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info