Manual Parkside PDT 40 C2 - IAN 96899 (page 23 of 28) (French)

595417

Zoom out

Zoom in

1/28

23 GB

Introduction / Safety of the fastener driving tool

In correspondence with conditions at the work loca-

tion, individual noise reduction measures may need

to be carried out, such as placing the workpiece on

a noise-suppressing surface, clamping or covering

to prevent workpiece vibration and adjusting to the

minimum pressure required by the work process. In

certain cases, wearing personal hearing protection

is require.

Wear hearing protection!

Vibration values in accordance with

ISO 8662-11:1999:

Vibration emission value a

h,W

= 15.0 m / s

Uncertainty K = 0.29 m / s

Mechanical impact (vibration)

The vibration value for the fastener driving device was

determined in accordance with ISO 8662-11:1999 —

Hand-held portable power tools – Measurement of

vibrations at the handle — Fastener driving tools

(see technical data). The value is referenced to the

device and does not represent the inﬂuence on the

hand-arm system when the device is used. Inﬂuence

on the hand-arm system when using the device de-

pends on e.g. gripping force, pressing force, work-

ing direction, air pressure set, the workpiece and its

position.

Safety of the fastener

driving tool

Please read

all the safety information and

instructions. Failure to comply with

the safety instructions and instructions can result in

severe injuries and / or damage to property.

PLEASE RETAIN ALL SAFETY INFORMATION

AND INSTRUCTIONS FOR FUTURE REFERENCE.

Each time before starting work, check

for flawless functioning of the safety

and triggering devices as well as the

firm fit of all bolts and nuts.

Do not conduct any improper manipu-

lation of the fastener driving tool.

Do not dismount or block any part of

the fastener driving tool, such a trig-

ger lock.

Do not conduct any „emergency re-

pairs“ with unsuitable materials.

The fastener driving tool must be reg-

ularly and properly maintained as

specified by the manufacturer.

Prevent anything that would weaken

or damage the device, e.g. by:

– stamping or engraving,

– alterations not permitted by the

manufacturer,

– guiding on templates made of hard

material, e.g. steel,

– permitting to fall onto or slide across

the floor,

– using as a hammer,

– every type of external force.

Work safety

Never point a fastener driving tool that

is ready to use directly at yourself,

other persons or animals.

During work, hold the fastener driving

tool so that head and body can not be

injured by possible kickback due to a

fault in the power supply or from hard

places in the workpiece.

Never trigger the fastener driving tool

into empty space. Following this instruction

will prevent danger due to uncontrolled ﬂying

fasteners and overloading the device.

Before transporting, disconnect the

fastener driving tool from the com-

pressed air network, particularly when

using ladders or are moving with an

unaccustomed body posture.

At the workplace, only carry the fas-

tener driving tool by its grip and never

with the trigger actuated.

Pay attention to workplace conditions.

Fasteners may strike completely through thin

workpieces or slide oﬀ corners or edges to

cause a danger to persons.

Introduction

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDT 40 C2 - IAN 96899 in the language / languages: French as an attachment in your email.

The manual is 1,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PDT 40 C2 - IAN 96899

Parkside PDT 40 C2 - IAN 96899 User Manual - English, German, Dutch - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PDT 40 C2 - IAN 96899 Manual

Product: