595345

Parkside PDOS 200 B2 - IAN 102876 Manual

45
Zoom out
Zoom in
Previous page
1/56
Next page
45
GB
Change grinding disc
Information on replace-
ment:
• Never operate the device without
protective equipment.
• Ensure that the rotation speed
stated on the grinding disc (
10) is the same or higher than
the nominal rotation speed of the
device.
• Ensure that the grinding disc
dimensions match those of the
device.
• Only use awless grinding discs
(sound test: an undamaged grind-
ing disc hanging freely on a
string will result in a clear sound
if it is tapped with a plastic ham-
mer).
• Never re-drill a locating hole
which is too small to make it
larger.
• Never use separate bushings or
adapters in order to make grind-
ing discs whose hole is too large
t the device.
• Do not use any saw blades.
• To clamp the grinding tools only
use the clamping ange provid-
ed. The pads between the clamp-
ing ange and the grinding tools
must be made of elastic materials
e.g., rubber, soft cardboard etc.
• Always reassemble the device
completely after replacing the
grinding disc.
Switch the device off and remove
the mains plug.
Allow the device to cool down.
Wear protective gloves when
changing the grinding discs in or-
der to avoid cutting damages.
The grinding disc nuts (10a) have
different threads (left-hand and
right-hand threads). To avoid dam-
aging the grinding disc spindle
thread (15), never mix up the two
grinding disc nuts (10a).
1. Undo the xing screws ( 7) and
remove the left-hand and right-
hand grinding disc cover (
8).
2. Unscrew the grinding disc nuts
(10a) by counter-holding the nut
on the opposite grinding disc with
a spanner (size 19 mm).
Unscrewing the left-hand nut (left-
hand thread):
turn clockwise.
Unscrewing the right-hand nut
(right-hand thread):
turn anticlockwise.
3. Remove the clamping ange (10b)
and the grinding disc (10).
4. Set up the new grinding disc (10)
with the intermediate shims (10c)
made of cardboard and the clam-
ping ange (10b) and manually
screw the grinding disc nut (10a)
on.
Screwing the left-hand nut (left-
hand thread) on:
turn anticlockwise.
Screwing the right-hand nut (right-
hand thread) on:
turn clockwise.
5. Screw the left hand and right
hand grinding disc covers (8) on.
6. Adjust the spark protection (
1)
and the workpiece support (
11) - the distance to the grinding
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDOS 200 B2 - IAN 102876 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDOS 200 B2 - IAN 102876 in the language / languages: French as an attachment in your email.

The manual is 3,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PDOS 200 B2 - IAN 102876

Parkside PDOS 200 B2 - IAN 102876 User Manual - English, German, Dutch, Danish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info