744067

Parkside PDOS 200 A1 IAN 56956 Manual

32
Zoom out
Zoom in
Previous page
1/46
Next page
32 GB/MT
J Do not use the mains lead to pull the plug out
of the mains socket. Protect the mains lead
from heat, oil and sharp edges.
12. Securely support the workpiece.
J Use clamps or a vice to grip the workpiece
firmly. This is much safer than holding it with
your hand.
13. Avoid placing your body in an
unnatural position.
J Keep proper footing and balance at all times.
14. Look after your tools carefully.
J Keep cutting tools sharp and clean. This way
you will work more safely and achieve better
results.
J Follow the advice on tool lubrication and con-
sumables replacement.
J Check the condition of the mains lead on your
electrical power tool regularly and have any
damage repaired by a competent specialist.
J Check the condition of extension leads regular-
ly and replace them if they are damaged.
J Keep handles and hand grips clean, dry and
free of oil and grease.
15. Pull the mains plug out of the mains
socket.
J Do this if the electrical power tool is not being
used, before carrying out maintenance tasks
on the electrical power tool and whenever you
are changing inserted tools, e.g. saw blades,
drills or router bits.
16. Make sure that no spanners, keys etc.
are left attached.
J Check before switching on that all spanners,
keys and setting tools have been removed.
17. Avoid unintentionally starting up the
device.
J Check that the switch is set to OFF on the de-
vice when the mains plug is inserted into the
mains socket.
18. Using an extension lead for working
outdoors.
J When working outside, always use an approved
and appropriately labelled extension lead.
19. Remain alert.
J Watch what you are doing. Proceed with cau-
tion. Do not use electrical power tools if you
cannot concentrate.
20. Check the electrical power tool for
damage.
J Before the electrical power tool is used, carefully
check the safety equipment and any slightly
damaged parts to see that they are still work-
ing properly.
J Check that all moving parts on the tool are
working properly, can move freely and are not
damaged. All parts must be correctly attached
and fulfil all the requirements necessary to allow
the electrical power tool to operate properly.
J Damaged safety equipment and components
must be properly repaired or replaced at a
competent electrical equipment repair centre
unless otherwise indicated in the operating in-
structions.
J Damaged switches must be replaced at a
Customer Service Centre.
J Never use an electrical power tool that cannot
be switched on and off properly.
21. CAUTION!
J The use of inserted tools and accessories other
than those recommended by the manufacturer
could lead to you being injured.
22. Have your electrical power tool
repaired at an electrical equipment
repair specialist.
J This electrical power tool complies with the
relevant safety regulations. Repairs may only
be carried out by a specialist electrical repair
centre using original spare parts, otherwise
injury could occur to the user.
Safety advice relating spe-
cifically to bench grinders
J
Do not touch the mains lead if it becomes damaged
or cut through while you are using the device.
Pull the plug out of the mains socket immediately
and have the device repaired by a suitably
qualified person or at your service centre.
J Do not operate the device if it is damp and do
not use it in a damp environment.
J If you use the device outdoors, always connect
it through a residual current device (RCD) with
a maximum trip current of 30 mA.
General safety advice
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDOS 200 A1 IAN 56956 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDOS 200 A1 IAN 56956 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 2,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PDOS 200 A1 IAN 56956

Parkside PDOS 200 A1 IAN 56956 Usermanual and installation guide - German, Dutch, French, Italian - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info