595411
29
Zoom out
Zoom in
Previous page
1/34
Next page
26
PDMS A1
GB
The mini die grinder must be operated and
maintained in accordance with the recommen-
dations contained in this manual to reduce any
unnecessary increase in vibration.
Consumables/machine tools must be selected,
maintained and replaced in accordance with
the recommendations in this guide in order to
avoid unnecessary increase in vibration.
Always use a stand, a clamp or a compensation
device to support the weight of the machine.
Hold the machine securely but not too fi rmly
while maintaining the necessary hand-reaction
force, as the vibration risk generally increases
the harder the machine is held.
An inadequately mounted or damaged ma-
chine tool can lead to excessive vibrations.
Additional safety instructions for
pneumatic machines
Compressed air can cause serious injury. Ensure
that the air supply is switched off , the hose
is not under pressure and that the machine
is disconnected from the air supply when the
machine is not in us, and also before exchang-
ing accessories or carrying out repairs. Never
aim the airfl ow towards yourself or any other
person.
Thrashing hoses can cause serious injury.
Therefore, always check that the hoses and
their fi xings are not damaged or have not come
loose.
If universal rotary joints (claw couplings) are
used, locking pins must be used to provide pro-
tection; Whipchek® air hose restraints must be
used to provide protection in case of a failure at
the connection of the hose to the machine.
Ensure that the maximum permissible pressure
stated on the machine is not exceeded.
Never carry compressed-air-powered machines
by the hose.
Hazards caused by accessories
Disconnect the grinder for whetstones from the
power supply before fi tting or replacing the
machine tools or accessories.
Use only accessories and consumables of the
size and type recommended by the manufacturer
of the grinder for whetstones.
Avoid direct contact with the machine tool during
and after use, since this can have heated up or
have become sharp.
The maximum operating speed recommended
by the manufacturer of the grinder for whetstones
must be the same or higher than the rotational
speed labelled on the machine.
Never fi t a grinding disc, cut-off disk or milling
cutter to a grinder for whetstones. A bursting
grinding disc can lead to extremely serious
injuries or death.
Do not use discs which are damaged, cracked
or could have fallen down.
Only approved machine tools with the correct
shaft diameter may be used.
Please note that you must ensure that the per-
missible rotational speed of small grinding
tools is reduced due to raising the position
of the shaft between the end of the chuck
and the small grinding tool (overhang). You
must ensure that the minimum clamping
length of 10 mm is retained. (see Figure 1)
min. 10 mm
Fig. 1
You must be aware that there is a danger of
mismatching between the shaft diameter of the
small grinding tool and of the chuck.
IB_43105_PDMSA1_LB1.indb 26IB_43105_PDMSA1_LB1.indb 26 14.05.14 11:1314.05.14 11:13
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDMS A1 - IAN 43105 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDMS A1 - IAN 43105 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PDMS A1 - IAN 43105

Parkside PDMS A1 - IAN 43105 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info