Manual Parkside PDM 600 A1 - IAN 322988 (page 21 of 84) (English, German, Dutch, French, Polish)

782072

Zoom out

Zoom in

1/84

16 GB/IE

Warning! During operation, this power tool produces an

electromagnetic ﬁeld. Under certain circumstances, this ﬁeld

may negatively aﬀect active or passive medical implants. In

order to reduce the danger of serious or fatal injuries, we rec-

ommend that individuals who wear medical implants should

consult their doctor and the manufacturer of the implant before

operating the power tool.

Operational Safety Instructions for the Wood Turn-

ing Lathe

• Familiarise yourself with the machine’s features and wood-

turning techniques before using the machine.

• Examine all workpieces for splits or knots. Glued joints must

set completely before turning.

• Ensure that the workpiece is securely locked in position and

all attachments are secured.

• Before turning the machine ON ensure that the workpiece

can rotate freely by rotating it by hand.

• Keep your hands and ﬁngers away from the rotating work-

piece.

• Switch the machine OFF and wait until it has come to a full

stop before making any adjustments on the workpiece, tail-

stock, or tool rest.

• Maintenance, adjustment, calibration and cleaning may

only be performed with the motor turned oﬀ.

• The machine is designed for use with wood-turning chisels

only.

• Always store away the wood-turning chisels safely before

you leave the workplace.

• Do not run the lathe without its covers and guards in place.

• Keep cutting tools sharp.

• Use the lowest speed when starting a new workpiece.

• Always stop the lathe at its slowest speed. If the lathe is run

so fast that it vibrates, there is a risk that the workpiece will

be thrown or the cutting tool jerked from your hands.

• Do not allow cutting tools to bite into the workpiece. The

wood could be split or thrown from the lathe.

• Always position the tool rest above the centre line of the

lathe when shaping a piece of stock.

• Before attaching a workpiece to the face plate, always rough

it out to make it as round as possible. This minimizes the vi-

brations while the piece is being turned. Always fasten the

workpiece securely to the faceplate. Failure to do so could

result in the workpiece being thrown away from the lathe.

• Use a brush or compressed air to remove wood shavings;

never your hands. The wood shavings will be sharp.

• The cutting tool must always be tight within the chuck and

adjusted to limit projection from the post. This will reduce the

possibility of the tool breaking or bending.

• Do not reach a cross the lathe while it is running.

• Only feed workpiece into a cutting tool against the direction

of rotation. The workpiece must always be rotating toward

you.

• Do not leave the tool unattended when it is plugged into an

electrical outlet. Turn oﬀ the tool, and unplug it from its electri-

cal outlet before leaving.

• This product is not a toy. Keep it out of reach of children.

• Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities, contains chemicals

known to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

-Lead from lead-based paints

-Crystalline silica from bricks and cement or other ma-

sonry products

-Arsenic and chromium from chemically treated lumber

• Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work

with approved safety equipment ,such as those dust masks

that are specially designed to ﬁlter out microscopic particles.

• People with pacemakers should consult their physician(s)

before use. Electromagnetic ﬁelds inclose proximity to heart

pacemaker could cause pacemaker interference or pace-

maker failure. In addition, people with pacemakers should:

-Avoid operating alone.

• Properly maintain and inspect to avoid electrical shock.

• The warnings, precautions, and instructions discussed in this

user manual cannot cover all possible conditions and situa-

tions that may occur. It must be understood by the operator

that common sense and caution are factors which cannot be

built into this product, but must be supplied by the operator.

Additional safety instructions for the use of face-

plates

• Ensure that the faceplate is the appropriate size to support

the workpiece.

• Ensure that the workpiece is securely fastened to the face-

plate.

• Rough cut the workpiece as close as possible to the ﬁnal

shape before mounting onto a faceplate.

• Only use scraping chisels for faceplate turning. Cutting chis-

els can easily be torn out of your hands.

• Pay attention that the woodturning chisel cannot interfere

with the holding screws at the ﬁnished dimensions of the

workpiece.

7. Remaining hazards

The machine has been built using modern technol-

ogy in accordance with recognized safety rules.

Some remaining hazards, however, may still exist.

• Only process selected woods without defects such as:

Branch knots, edge cracks, surface cracks. Wood with such

defects is prone to splintering and hazardous.

• Wood which is not correctly glued can explode when being

processed due to centrifugal force.

• Trim work piece to a rectangular shape, center and correctly

secure before processing. Unbalanced work pieces can be

hazardous.

• Injuries can occur when feeding work pieces if tool supports

are not correctly adjusted or if turning tools are blunt. Sharp

turning tools which are free of defects are necessary for pro-

fessional turning.

• Long hair and loose clothing can be hazardous when the

work piece is rotating. Wear personal protective gear such

as a hair net and tight ﬁtting work clothes.

• Saw dust and wood chips can be hazardous. Wear person-

al protective gear such as safety goggles and a dust mask.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDM 600 A1 - IAN 322988 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 4.38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PDM 600 A1 - IAN 322988 Manual

Product: