595405
36
Zoom out
Zoom in
Previous page
1/39
Next page
36 GB
extraction. To do so, open the hook-and-loop
fastener at the side of the dust bag
10
.
Adding oil
To ensure a long service life for the compressed air
orbital sander the unit must always be adequately
filled with pneumatic oil.
You may ensure this in any of the follow-
ing ways:
Connect a service unit with an oiler to the
compressor.
Install a compressed air oiler in the air line or
to the compressor.
Manually add approx. 3-5 drops of pneumatic
oil to the plug nipple
3
every 15 operating
minutes.
Initial use
Connecting the compressed
air source
Note: Only operate the compressed air orbital
sander with cleaned, condensate-free compressed
air. Never exceed the unit‘s maximum operating
pressure of 7.5 bar.
Note: The compressed air source must be fitted
with a (filter) / pressure reducer to allow the air
pressure to be regulated.
Switching on and off
Note: Always switch on the compressed air orbit-
al sander before bringing it into contact with the
work piece.
Switching on the compressed air orbital
sander:
Press the operating lever
1
all the way down
(see Fig. C).
Adjust the speed with the speed control
5
.
Switching off the compressed air orbital
sander:
Release the control lever
1
.
Disconnect the unit from the compressed air
source after finishing the work.
Note: First disconnect the hose from the
compressed air source (compressor), only then
disconnect the supply hose from the unit. This
will ensure that the compressed air supply hose
does not wave around or recoil in an uncon-
trolled manner.
Working instructions
Wait until the device has come to a standstill
before you put it down.
Sanding surfaces
Switch on the compressed air orbital sander,
place the entire sanding surface on the surface
to be worked and move it across the work
piece with moderate pressure (see Fig. D).
Note: The sanding output and pattern greatly
dependent on the sanding disc selected and
the pressure applied. Only grinding discs that
are in perfect condition will provide good
grinding performance.
Be sure to apply pressure evenly to increase
the life of the sanding discs.
A sanding sheet previously used on metal must
not be used on other materials.
Replacing the backing plate
RISK OF INJURY! Always
disconnect the device from the compressed air
source before you replace the backing plate
6
.
Push the open-ended spanner
11
between the
backing plate
6
and collar
7
.
Release the backing plate
6
by turning the
plate anticlockwise and holding the open-ended
spanner
11
still against this movement.
Working … / Cleaning / Information about warranty and service processing
Before Initial Use / Initial use / Working instructions
96905_par_Druckluft_Exzenterschleifer_content_DE_AT_NL.indd 36 30.04.14 15:46
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDEXS 150 A1 - IAN 96905 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDEXS 150 A1 - IAN 96905 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PDEXS 150 A1 - IAN 96905

Parkside PDEXS 150 A1 - IAN 96905 User Manual - Danish, French, Swedish, Finnish - 81 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info