722840
21
Zoom out
Zoom in
Previous page
1/164
Next page
21
GB IE
Removing the battery pack:
Push the release button ( 11a)
and pull the battery pack
(11) out towards the front of
the device.
Choice of gear
Slide the gear selector (
4) to 1 or 2,
corresponding to a low or high torque
selection.
A gear change may only be per-
formed in standstill mode!
Set the direction of rotation
You can select the direction of rotation
with the direction switch (clockwise and
anticlockwise direction) and secure the de-
vice against accidental start up.
1. Wait for the device to shut-down.
2. Clockwise direction:
Press direction switch (6) to
the right.
3. Anticlockwise direction:
Press direction switch (6)
to the left.
4. Switch lock: Bring direction
switch to neutral position.
The direction changed may only be
performed in standstill mode.
Torque setting
You can preset the maximum torque by ro-
tating the torque adjustment ring (
3).
25 torque settings + 1 drill setting are
provided.
1. Turn the adjusting ring (
3) to select
the desired torque:
Step 1 --> lowest torque,
Step
--> highest torque.
Screws: Steps 1 - 19
Drilling: Step
.
2. Start with a lower torque step and in-
crease according to requirement.
Torque adjustment should only be
performed in standstill mode.
Reaching the preset torque limit pro-
duces a noticeable rasping sound.
This sound is caused by the slip clutch.
Tool change
1. Rotate the keyless chuck (2) coun-
ter-clockwise, until the drill chuck
aperture (11) is large enough to
accommodate the tool.
2. Push the tool as far as possible into
the keyless chuck (2).
3. Rotate the chuck clockwise to
clamp the tool rmly.
4. To remove the tool again, rotate the
keyless chuck (2) and pull out the tool.
Switching on/off
By using the on/off switch (
5) you can
progressively control the speed. The longer
you push the on-off button, the higher the
speed.
1. Press the on/off switch (5) to start
the device. The LED work light
(10) lights up during operation.
2. To turn it off, release the on/off
switch (5).
When you move the direction
s
witch (6) to the middle position,
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PBSA 20-Li A1 - IAN 313555 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PBSA 20-Li A1 - IAN 313555 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info