595336

Parkside PBH 1050 A1 - IAN 102964 Manual

7
Zoom out
Zoom in
Previous page
1/58
Next page
7 GB/IE
Introduction Introduction / General power tool safety warnings
Main handle
Hammer drilling in
Concrete: a
h(HD)
= 9.853 m / s
2
,
K = 1.5 m / s
2
Additional handle
Hammer drilling in
Concrete: a
h(HD)
= 8.967 m / s
2
, K = 1.5 m / s
2
Main handle
Chiselling: a
h(CHeq)
= 12.738 m / s
2
,
K = 1.5 m / s
2
Additional handle
Chiselling: a
h(CHeq)
= 8.278 m / s
2
,
K = 1.5 m / s
2
The vibration level specified in
these instructions was measured in accordance with
an EN 60745 standardised measurement process
and can be used to compare equipment. The vibra-
tion emission value specified can also serve as a
preliminary assessment of the exposure.
The vibrati
on level may change with the application
of the tool and in some cases may be higher than
the value specified in these instructions. Regularly
using the electric tool in such a way may make it
easy to underestimate the vibration.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particu-
lar period of work, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can clearly reduce the vibration load through-
out the work period.
General power tool
safety warnings
Read all safety
warnings and all instructions.
Failure to follow the warnings and in-
structions may result in electric shock, fire and / or
serious injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-op-
erated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) D
o not operate power tools in explosive
atmospheres, such as in the presence
of flammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away
while operating a power tool. Distractio
ns
can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plug
s
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or
wet conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk
of electric shock.
e)
When operating a power tool outdo
ors,
use an extension cord suitable for out-
door use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
… 7 …


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pbh-1050-a1---ian-102964

Reset search

  • Hello, I need a Switch on/off for my Parkside Rotary Hammer PBH 1050 A1, is it available Please. Thanks.
    Regards
    Pio Submitted on 21-5-2021 at 14:19

    Reply Report abuse

  • How do you remove and replace a keyless chuck on a Parkside PBH 1050 A1 hammer drill?
    Submitted on 14-5-2020 at 12:08

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PBH 1050 A1 - IAN 102964 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PBH 1050 A1 - IAN 102964 in the language / languages: English, German, Dutch, French, Swedish, Finnish as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info