679268
23
Zoom out
Zoom in
Previous page
1/89
Next page
PASSK 20-Li A1
GB
IE
19
Before use
Charging the battery pack (see fig. A)
CAUTION!
Always pull out the power plug before you
remove the battery pack from or connect the
battery pack to the charger.
Never charge the battery pack
when the
ambient temperature is below 10°C or above
40°C.
Connect the battery pack to the high-speed
battery charger (see Fig. A).
Insert the power plug into the socket. The control
LED
lights up red.
The green LED
indicates that the charging
process is complete and the battery pack
is ready for use.
CAUTION!
If the red control LED
flashes, this means
that the battery pack has overheated and
cannot be charged.
If the red and green control LEDs both
flash, this means that the battery pack is
defective.
Push the battery pack
back into the appliance.
Switch off the charger for at least 15 minutes
between successive charging sessions. Also dis-
connect the power plug from the mains power
socket.
Attaching/disconnecting the battery
pack to/from the appliance
Attaching the battery pack:
Push the rotation direction switch
into the
middle position (lock). Push the battery pack
into the handle until it clicks into place.
Removing the battery pack:
Press the release button
and remove the
battery pack
.
Checking the battery charge level
Press the battery charge level button to check
the status of the battery (see also main diagram).
The status/remaining charge will be shown
on the battery display LED
as follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Use
Switching on and off
Switching on:
To start the appliance, press the ON/OFF
switch
and keep it pressed in.
The LED working light lights up when the
ON/OFF switch is depressed lightly or fully.
This provides illumination of the work area in
poor lighting conditions.
Switching off:
Release the ON/OFF switch
to switch off the
appliance.
Setting/preselecting the rotation
speed/tightening torque
Press the torque preselection button to select
the required torque in stages.
Press the ON/OFF switch lightly for a low
speed/tightening torque. Increasing the pres-
sure increases the speed/tightening torque.
The tightening torque depends on the selected
speed/torque preselection and impact duration.
NOTE
However, to tighten lug nuts, the smallest
torque setting must be selected to avoid over
tightening.
CAUTION!
The tightening torque actually attained must
always be checked with a torque wrench!
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PASSK 20-Li A1 - IAN 305077 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PASSK 20-Li A1 - IAN 305077 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info