679459

Parkside PAS 4 B3 - IAN 303832 Manual

11
Zoom out
Zoom in
Previous page
1/43
Next page
GB
│
IE
│
NI
│
CY 
│
 7 ■
PAS 4 B3
Before use
Charging the appliance battery
(see fig. A)
NOTE
►
The battery is supplied partially charged.
Before first use, charge the battery in the
charger for at least 1 hours. This guarantees
full battery power. Li-ion batteries can be
charged at any time without adversely
affecting their service life. Interruption of the
charging process will not damage the
battery.
► If the battery charge level indicator lights
up red during use, the battery is at less than
30% of its capacity and needs to be
charged.
► Never charge the cordless appliance when
the ambient temperature is below 10°C or
above 40°C. If a lithium-ion battery is to be
stored for an extended period, the charge
level should be checked regularly. The
optimum charge level is between 50% and
80%. The storage climate should be cool and
dry and the ambient temperature should be
between 0°C and 50°C.
Start charging:
♦ Connect the micro USB plug of the charging
cable
9b
to the charging socket .
♦ Connect the USB plug of the charging cable
9a
to the charger .
♦ Connect the charger to a 100–240 V ∼
50/60 Hz power source.
The battery is fully charged when the battery level
display changes from red to green.
Stopping charging:
♦ Disconnect the charger from the mains
power supply.
♦ Disconnect the micro USB plug of the charging
cable
9b
from the charging socket .
Assemble the attachments
Usage:
- With the torque attachment
screwing stops as
soon as the screw is tight. Set the required torque
from one of the 10 levels.
- The eccentric attachment
allows you to screw
even in locations that are close to the wall.
- The angle attachment
allows you to screw at
right angles.
- The cutting attachment
allows you to cut soft
materials, such as card and similar materials up to
a thickness of 6 mm.
Assembly:
NOTE
►
Before carrying out any work on the appli-
ance, ensure that the rotation direction switch
is in the middle. This prevents unintentional
switching on.
♦ Start by removing the rubber cap from the tool
holder (see fig. B).
♦ Now you can fit the supplied attachments to the
appliance in 45° steps. Fit the attachment onto
the appliance so that the attachment clicks into
place. (see fig. C, example: torque attachment
).
Dismantling:
♦ To remove the attachments from the appliance,
press the release button and pull the attach-
ment off forwards.
♦ Afterwards, replace the rubber cap on the tool
holder.
… 11 …


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pas-4-b3---ian-303832

Reset search

  • Transmission from the gearbox to the screwdriver head Submitted on 15-6-2020 at 01:03

    Reply Report abuse

  • I've got a shift lever from the gearbox to the screwdriver's broken head. I want the length of that arm so I can replace it with another one Submitted on 15-6-2020 at 01:01

    Reply Report abuse

  • i just bought this and was good at 1st trial...and than it doest work yet...i"ve charged it but still the same...any help please... Submitted on 14-11-2019 at 00:25

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PAS 4 B3 - IAN 303832 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PAS 4 B3 - IAN 303832 in the language / languages: English as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PAS 4 B3 - IAN 303832

Parkside PAS 4 B3 - IAN 303832 User Manual - German, Dutch, French - 41 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info