Manual Parkside PAMFW 10.8 A1 - IAN 96269 (page 27 of 34) (French)

576740

Zoom out

Zoom in

1/34

27 GB

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 74.33 dB(A)

Sound power level: 85.33 dB(A)

Uncertainty K: 3 dB

Wear ear protection!

The total vibration (vector sum of three directions) is

calculated in accordance with EN 60745:

Sanding:

Vibration emission value a

= 2.590 m / s

Uncertainty K = 1.5 m / s

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions. Re-

gularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

General safety advice for

electrical power tools

Read all the safety advice

and instructions! Failure to observe the safety

advice and instructions may result in electric shock,

ﬁre and / or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electricity

(by means of a mains lead) and electrical tools pow-

ered by rechargeable batteries (without a mains lead).

1. Workplace safety

a) K

eep your working area clean and wel

lit. Untidy or poorly lit working areas can lead

to accidents.

b) Do not work with the device in poten-

tially explosive environments in which

there are inflammable liquids, gases o

dusts. Electrical power tools create sparks,

which can ignite dusts or fumes.

c) Keep children and other people away

while you are operating the electrical

tool. Distractions can cause you to lose con-

trol of the device.

2. Electrical safety

a) The mains plug on the power tool (or

on the power supply) must ﬁt the

mains

socket. Never modify the plug in any

way. Never use adapter plugs with

earthed power tools. Unmodiﬁed plugs

and the correct sockets reduce the risk of elec-

tric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed.

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d) Do not use the mains lead for any pur-

pose for which it was not intended, e.

to carry the device, to hang up the de-

vice or to pull the mains plug out of

the mains socket. Keep the mains lead

away from heat, oil, sharp edges or

moving parts of the device. Damaged or

tangled mains leads increase the risk of elec-

tric shock.

Introduction / General safety advice for electrical power toolsIntroduction

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PAMFW 10.8 A1 - IAN 96269 in the language / languages: French as an attachment in your email.

The manual is 2,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PAMFW 10.8 A1 - IAN 96269

Parkside PAMFW 10.8 A1 - IAN 96269 User Manual - English, German, Dutch - 34 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PAMFW 10.8 A1 - IAN 96269 Manual

Product: