796085

Parkside PAKSP 20-Li A1 - IAN 308540 Manual

19
Zoom out
Zoom in
Previous page
1/85
Next page
GB│IE │ 15 ■
PAKSP 20-Li A1
Technical specifications
Cordless cross cut mitre saw PAKSP 20-Li A1
Rated voltage 20 V (DC)
Rated idle speed n0 4300 rpm
Max. cutting width/depth at 90 x 90° 120 x 60 mm
90 x 45° 80 x 60 mm
45 x 90° 120 x 35 mm
45 x 45° 80 x 35 mm (right)
45 x 45° 60 x 35 mm (left)
Pivoting range (table) - 45°/+ 45°
Mitre cut 0–45° to the left
Saw blade
210 mm
Ø 210 x 30 mm, 48 teeth,
Tooth width: max. 2 mm
Battery PAP 20 A3
Type LITHIUM ION
Rated voltage 20 V (DC)
Capacity 4 Ah (80 Wh)
Cells 10
High-speed battery charger PLG 20 A3
INPUT
Rated voltage 230–240 V ∼ (AC), 50 Hz
Rated power consumption: 120 W
Fuse (internal) 3.15 A T3.15A
OUTPUT
Rated voltage 21.5 V (DC)
Rated current 4.5 A
Charging time approx. 60min.
Protection class II / (double insulation)
Wear ear muffs!
Read the operating
instructions before use!
Noise emission value
Noise measurement value determined in accordance with EN 62841.
The A-rated noise level of the power tool is typically:
Sound pressure level LPA = 83.2 dB (A)
Uncertainty K KPA = 3 dB
Sound power level LWA = 94.2 dB (A)
Uncertainty K KWA = 3 dB
Wear ear muffs!
Vibration emission value
Total vibration values (vector total of three directions) determined in
accordance with EN 62841:
Sawing wood ah,W = 2.03 m/s2
Uncertainty K = 1.5 m/s2
NOTE
► The vibration emission values and the noise emission values given in
these instructions have been measured in accordance with a standard-
ised test procedure and can be used for comparison of the power
tool with another tool.
► The specified total vibration values and the noise emission values can
also be used to make a provisional load estimate.
WARNING!
► Depending on the manner in which the power tool is being used, and
in particular the kind of workpiece being worked, the vibration and
noise emission values can deviate from the values given in these
instructions during actual use of the power tool.
► Try to keep the vibration load as low as possible. Measures to reduce
the vibration load are, e.g. wearing gloves and limiting the working
time. Wherein all states of operation must be included (e.g. times
when the power tool is switched off and times where the power tool is
switched on but running without load).
General power tool safety warnings
WARNING!
►Read all safety warnings, instructions, illustrations and specifica-
tions provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased risk
of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
e) When working outdoors with an electrical power tool always use
extension cords that are also suitable for use outdoors. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PAKSP 20-Li A1 - IAN 308540 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PAKSP 20-Li A1 - IAN 308540 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info