576605

Parkside PABS 18-Li B4 - IAN 100086 Manual

10
Zoom out
Zoom in
Previous page
1/65
Next page
10 GB/IE
cause kickback. The inserted tool may jam if the
electrical power tool is overloaded or is held at
an angle to the workpiece.
Before you carry out any tasks on the
device, transport or store it, make sure
that the direction of rotation switch is
in the middle position (lock). To prevent
the device from starting up unintentionally.
DANGER! Take steps to ensure that
you do not hit upon any service lines
(electricity, gas, water) when work-
ing with electrical appliances. Check, if
need be with a service line detector, before you
start to cut or bore into a surface.
Original ancillaries /
accessories
Use only the ancillaries and accessories
that are detailed in the operating in
struc-
tions. The use of ancillaries and accessories
other than those recommended in the operating
instructions could lead to an increased risk of per-
sonal injury for you.
Start-up
Charging the battery pack
CAUTION! Always ensure the plug is removed
from the mains socket before inserting a battery pack
into, or removing one from, the charging station.
Never charge the battery pack if the ambient
temperature is less than 10 °C or greater than
40 °C.
1. Insert the battery pack
6
into the quick-
charger
13
(see Fig. C).
2. Insert the mains plug into the mains socket. The
flashing green charge indicator LED
15
shows
that charging is in progress.
3. The charging process is completed when the
green charge indicator LED
15
light up and the
accumulator pack
6
is ready for operation.
4. If the red charge indicator LED
14
lights up, the
quick battery charger
13
is in standby mode;
the accumulator pack
6
is not connected.
5. If the red charge indicator LED
14
starts flas-
hing, this means that the accumulator pack
6
has become too hot; no charging process.
Never charge the battery pack for a second time
immediately after a fast charging process has
been completed. This can give rise to the battery
pack becoming overcharged and to a reduced
service life of the battery and charging station.
Switch the charger off for at least 15 minutes
between two successive charging procedures.
Remove the power plug from the wall socket.
Insertion / removal of a battery
pack into the appliance
Inserting the rechargeable battery pack:
Move the rotation switch
2
into the middle
position (lock). Push the rechargeable battery
pack
6
into the handle until it engages.
Removing the rechargeable battery pack:
Press the release button
7
and remove the
rechargeable battery pack
Checking battery status
To check the battery status, press the battery
LED button
9
(refer to main diagram).
The three battery LEDs
8
indicate the condition
and the remaining charge as follows:
GREEN / RED / ORANGE = maximum charge /
capacity
RED / ORANGE = medium charge / capacity
RED = weak charge – recharge battery
Changing tools
Your cordless drill has a fully automatic spindle
lock
.
Start-up / OperationGeneral safety advice for electrical power tools / Start-up
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PABS 18-Li B4 - IAN 100086 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PABS 18-Li B4 - IAN 100086 in the language / languages: English, German, Dutch, Danish, Swedish, Finnish as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info