576607

Parkside PABS 14.4 A1 - IAN 102649 Manual

30
Zoom out
Zoom in
Previous page
1/34
Next page
30 GB
General safety advice for electrical power tools / Start-up
prepared for high reaction torques as they may
cause kickback. The inserted tool will jam if it is
overloaded or if it becomes stuck in the work-
piece.
When working on the device as well
as transporting or storing it, put the
rotary direction switch in the middle
position (lock). Therefore preventing the
power tool from starting unintentionally.
DANGER! Check that you will not hit
electric, gas or water lines whilst using
the power tool. Check, if need be with a
service line detector, before you start to cut or
bore into a surface.
Original accessories / tools
Use only the accessories and attachmen
ts
detailed in the operating instructions,
or those which are compatible with
the device.
Start-up
Charging the battery pack
CAUTION! Always ensure the plug is removed
from the mains socket before inserting a battery pack
into, or removing one from, the charging station.
Never charge the battery pack if the ambient
temperature is less than 10 °C or greater than
40 °C.
1. Insert the battery pack
4
in the quick charger
11
(see Fig. C).
2. Insert the mains plug into the mains socket. The
status LED
12
will light up red.
3. The green charging status LED
13
indicates the
charging process has been completed and the
battery pack
4
is ready for use.
4. Slide the battery pack
4
into the unit.
Never charge the battery pack for a second time
immediately after a fast charging process has
been completed. This can give rise to the battery
pack becoming overcharged and to a reduced
service life of the battery and charging station.
Switch the charger off for at least 15 minutes
between two successive charging procedures.
Remove the power plug from the wall socket.
Insertion / removal of a battery
pack into the appliance
Inserting the rechargeable battery pack:
Move the rotary direction switch
2
into the
middle position (lock). Push the rechargeable
battery pack
4
into the handle until it engages.
Removing the rechargeable battery pack:
Press the release button
5
and remove the
rechargeable battery pack
Checking battery status
Press the battery LED
7
to check the battery
condition (also see main image). The battery
display LED
6
will indicate the status or the
remaining charge as follows:
GREEN / RED / ORANGE = maximum charge /
capacity
RED / ORANGE = medium charge / capacity
RED = weak charge – recharge battery
Changing tools
Your cordless drill has a fully automatic spindle
lock
.
When the motor stops the power train will lock so
that you can open the drill chuck
9
by turning
it.
After you have inserted the required bit and fixed it
in place by turning the chuck
, you can immedi-
ately continue working. The spindle lock releases
itself automatically when the motor is started (by
operation of the ON / OFF switch
3
).
Start-up / Operation
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PABS 14.4 A1 - IAN 102649 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PABS 14.4 A1 - IAN 102649 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info