456006
10
Zoom out
Zoom in
Previous page
1/55
Next page
10 GB/IE
General safety advice for electrical power tools / Before first use
WARNING!
The inserted tool may
strike concealed electricity cables,
therefore when working you must
hold the electrical power tool by the
insulated handle areas only. Contact
with a live wire means that the metal parts of
the electrical power tools may become live and
this can result in an electric shock.
J Before you carry out any tasks on the
device, transport or store it, make sure
that the direction of rotation switch is
in the middle position (lock). To prevent
the device from starting up unintentionally.
J Children or persons who lack the knowledge or
experience to use the device or whose physical,
sensory or intellectual capacities are limited
must never be allowed to use the device without
supervision or instruction by a person responsi-
ble for their safety. Children must never be
allowed to play with the device.
Q
Attention - Service lines!
WARNING!
Take steps to ensure that
you do not hit upon any service lines
(electricity, gas, water) when working
with electrical appliances. Check, if need be
with a service line detector, before you start to cut
or bore into a surface.
Q
Original ancillaries /
accessories
J Use only the ancillaries and accessories
that are detailed in the operating
instructions. The use of ancillaries and ac-
cessories other than those recommended in the
operating instructions could lead to an in-
creased risk of personal injury for you.
Q
Before first use
Q
Removing / charging / inserting
rechargeable battery pack
Note: The battery is supplied partially charged.
Charge the battery in the charging station for at
least three hours before first use. By doing this the
battery will operate at its highest capacity. You can
charge the Li-Ion battery at any time without risk of
shortening battery life. Interrupting the charging
process does not damage the battery.
1. In order to remove the rechargeable battery pack
8
, press the release buttons
9
and take the
rechargeable battery pack
8
out of the device.
2. Place the charging cap
16
onto the rechargeable
battery pack
8
.
3. Place the power supply unit
13
into the socket.
The status LED
14
will shine red.
4. The green charge indicator LED
15
shows you
that the charging process is complete and the
battery pack
8
is ready for use.
5. Insert the rechargeable battery pack
8
into
the device.
Q
Checking the battery status
j To check the battery status, press the button for
the rechargeable battery LED
2
(refer to main
diagram). The status or the remaining power
will be displayed in the rechargeable battery
LED
3
as follows:
RED / ORANGE / GREEN = maximum charge /
performance
RED / ORANGE = medium charge / performance
RED = low charge – recharge battery
Q
Changing tools
Your cordless drill / screwdriver has a fully automat-
ic spindle lock
.
Once the motor has come to a halt, the drive shaft
is automatically locked, so that the chuck
12
can
be opened simply by turning it
.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PABS 10.8 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PABS 10.8 A1 in the language / languages: English, Danish, Swedish, Finnish as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PABS 10.8 A1

Parkside PABS 10.8 A1 User Manual - German, Dutch, French, Italian - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info