Manual Parkside MPKZ 2000 A1 - IAN 315340 (page 14 of 68) (English, German, Dutch, French)

706349

Zoom out

Zoom in

1/68

9GB/IE/NI

8.3 Crosscut 90° and turntable 0° (ﬁg. 1/2/7)

In the case of cutting widths up to approx. 100 mm it is possible

to ﬁx the traction function of the saw with the set screw (20) in

the rear position. In this position the machine can be operated

in cross cutting mode. If the cutting width is over 100 mm then

it is necessary to ensure that the set screw (20) is loose and the

machine head (4) can move.

Attention! For 90° crosscuts, the moveable stop rail (16a) must

be ﬁxed in the inner position.

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) inwards.

• The moveable stop rail (16a) must be locked in a position far

enough from the inner position that the distance between the

stop rail (16a) and the saw blade (6) is no more than 8 mm..

• Before making the cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Re-tighten the set screw (16b).

• Move the machine head (4) to its upper position.

• Use the handle (1) to push back the machine head (4) and ﬁx

it in this position if required (dependent on the cutting width).

• Place the piece of wood to be cut at the stop rail (16) and

on the turntable (14).

• Lock the material with the clamping devices (7) on the ﬁxed

saw table (15) to prevent the material from moving during

the cutting operation.

• Release the lock switch (3) and press the ON/OFF switch

(2) to start the motor. (Refer also to point 8.13 “Changing

the speed” in this regard.)

• With the drag guide (21) ﬁxed in place (21):

use the handle (1) to move the machine head (4) steadily

and with light pressure downwards until the saw blade (6)

has completely cut through the work piece.

• With the drag guide (21) not ﬁxed in place (21):

pull the machine head (4) all the way to the front. Lower the

handle (1) to the very bottom by applying steady and light

downward pressure. Now push the machine head (4) slowly

and steadily to the very back until the saw blade (6) has

completely cut through the work piece.

• When the cutting operation is completed, move the machine

head back to its upper (home) position and release the ON/

OFF button (2).

Attention! The machine executes an upward stroke auto-

matically due to the return spring, i.e. do not release the han-

dle (1) after completing the cut; instead allow the machine

head to move upwards slowly whilst applying light counter

pressure.

8.4 Crosscut 90° and turntable 0° - 45°

(ﬁg. 1/7/8)

The sliding compound mitre saw can be used to make crosscuts

of 0° -45° to the left and 0° -45° to the right in relation to

the stop rail.

Important! For 90° crosscuts, the moveable stop rail (16a)

must be ﬁxed in the inner position.

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) inwards.

• The moveable stop rail (16a) must be ﬁxed far enough in

front of the innermost position that the distance between the

stop rail (16a) and the saw blade (6) amounts to a minimum

of 8 mm.

• Before making the cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Loosen the locking handle (11) if tightened, pull up the

latched position lever (35) with your index ﬁnger and use

the locking handle (11) to set the rotary table (14) to the

desired angle.

• The pointer (12) on the rotary table must match the desired

angle on the scale (13) on the ﬁxed saw table (15).

• Re-tighten the locking handle (11) to secure the rotary table

(14).

• Cut as described under section 8.3.

8.5 Precision adjustment of the stop for mitre cut

45° (ﬁg. 1/2/5/9/10)

• No stop angle included.

• Lower the machine head (4) and secure it using the locking

bolt (23).

• Fix the rotary table (14) in the 0° position.

Attention! For mitre cuts (inclined saw head), the left side of

the moveable stop rails (16a) must be ﬁxed in the outer posi-

tion.

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) outwards.

• The moveable stop rail (16a) must be ﬁxed far enough in

front of the innermost position that the distance between the

stop rail (16a) and the saw blade (6) amounts to a maxi-

mum of 8 mm.

• The right side of the moveable stop rails (16a) must be in

the inner positiion.

• Before making a cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Loosen the set screw (22) and use the handle (1) to angle

the machine head (4) 45° to the left.

• 45° - position angle stop (B) between the saw blade (6) and

rotary table (14).

• Loosen the lock nut (27a) and adjust the adjustment screw

(27) until the angle between the saw blade (6) and the ro-

tary table (14) is precisely 45°.

• Re-tighten the lock nut (27a).

• Subsequently check the position of the angle indicator. If

necessary, loosen the pointer (19) using a Philips screwdriv-

er, set to position 45° on the angle scale (18) and re-tighten

the retaining screw.

8.6 Mitre cut 0°- 45° and turntable 0°

(ﬁg. 1/2/11)

The sliding compound mitre saw can be used to make mitre cuts

of 0° - 45° in relation to the work face.

Attention! For mitre cuts (inclined saw head), the left side of

the moveable stop rails (16a) must be ﬁxed in the outer posi-

tion.

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) outwards.

• The moveable stop rail (16a) must be ﬁxed far enough in

front of the innermost position that the distance between the

stop rail (16a) and the saw blade (6) amounts to a minimum

of 8 mm.

• The right side of the moveable stop rails (16a) must be in

the inner positiion.

Parkside mpkz2000...when loosening saw blade Allen nut is it turned clockwise or anticlockwise Submitted on 19-2-2022 at 10:05
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside MPKZ 2000 A1 - IAN 315340 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside MPKZ 2000 A1 - IAN 315340 Manual

Product: