558598
11
Zoom out
Zoom in
Previous page
1/72
Next page
www.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++
11
k
1111
wwww.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++
IMPORTANT SAFETY ADVICE ƽ
̅ To be read in conjunction with the advice in the accompanying booklet on safety before using for the
first time.
̅ The PEH 950 power planer is intended to be used for planing wood (e.g. beams, boards).
̅ If the mains cable is damaged or cut through during the work - never touch the cable - pull out the
mains plug immediately. Never use electrical equipment with damaged cables.
̅ For operating the planer for longer periods and particularly if dust that may be hazardous to heath is
created, the planer should be connected to a suitable external vacuum device.
Wear a dust mask.
̅ Make sure you only use sharp blades.
̅ Always keep the power cable fed to the rear of the machine.
̅ Never plane over metal objects, nails or screws.
̅ Only place the planer against the workpiece after switching it on.
̅ The base plate ¾ must always lay flat on the workpiece when working.
̅ Do not clear dust etc. from the dust outlet º with your fingers. Use a piece of wood to dislodge any
trapped planing debris.
OPERATION
The PEH 950 power planer has INTELLIGENT POWER CONTROL.
This electronic management system monitors and controls your power planer
in its various operating states;
Operating state Feature
Switching On/Off: The IPC electronic system start-up mode ensures that the
motor starts up slowly and gently. This large ly avoids
heavy transient current surges, and means that electrical safety cut-out
devices are not generally tripped (building sites, domestic premises).
No-load running: After switching on, the IPC electronic management system run-up mode
takes the planer speed up to the pre-set required value. After this is reached,
the IPC system speed control mode keeps the grinder operating at a
constant speed.
W
ARNING:
Always remove the plug from the mains socket before working on the planer.
Take note of the mains voltage. The voltage must agree with that shown on the rating plate
(equipment shown as 230 V can also be used with 220 V).
ON / OFF SWITCH
On the grounds of safety the ON / OFF switch
» cannot be locked in the ON position for continuous
operation. It must always be pressed during operation.
11
t
ƽ
BA_Ident.-No._PEH950-102003-1 21.01.2004 13:33 Uhr Seite 11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside KH 3131 - PEH 950 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside KH 3131 - PEH 950 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info