Manual Parkside KH 3041 (page 26 of 37) (English, German, Dutch, Italian, Portuguese, Spanish)

464929

Zoom out

Zoom in

1/37

26 GB/MT

NOTE: Fine adjustment can also be done using

the knurled screw

j Turn the knurled screw

in the direction of

the lower stop

in order to sink the fastener

more deeply into the work piece.

j Turned the knurled screw

in the direction of

the upper stop

in order to sink the fastener

less deeply into the work piece.

NOTE: The compressed air tacker can be used on

a horizontal or on a vertical workpiece.

j Turn the exhaust cover

to direct the escap-

ing air in the desired direction.

j After you ﬁnish work, disconnect the device

from the compressor.

NOTE: First disconnect the hose from the

compressor and only then disconnect the

compressed air supply hose from the device.

This will ensure that the compressed air supply

hose does not wave around in an uncontrolled

manner.

Maintenance and cleaning

J DANGER OF BURNS! Do not start any

cleaning or maintenance work on the com-

pressed air tacker until it has completely

cooled down.

J DANGER OF INJURY! Always disconnect

the device from the compressed air source

before you clean or maintain it.

Maintenance

j Grease the device regularly. This will ensure

that it continues to work properly and has a

long service life.

Lubrication with the oil mist lubricator

NOTE: As an air preparation stage downstream

of the pressure reducer, an oil mist lubricator pro-

vides a continuous, optimum level of lubrication to

the compressed air tacker. An oil mist lubricator

gives oﬀ ﬁne droplets of oil into the air and thus

ensures controlled lubrication.

j Install the oil mist lubricator downstream of the

(ﬁlter)/pressure reducer. To do this, insert the

plug-in nipple of the oil mist lubricator into the

quick-release coupling of the (ﬁlter)/pressure

reducer.

j Then connect the compressed air device to the

quick-release coupling provided for it.

Manual lubrication

NOTE: If you do not have an oil mist lubricator,

you must lubricate the device before each period

of use and/or after long periods of disuse.

j Place 3 - 5 drops of compresses air special oil

into the threaded plug-in nipple

of the

compressed air tacker.

j Then press the trigger

a few times.

j Introduce 5 - 10 drops after a period of

disuse of more than 5 days.

Cleaning

J Do not use sharp objects for cleaning the

device. Do not allow any liquids to enter the

device. Otherwise the device could be damaged.

j Clean the device frequently; for best results, do

this immediately after you have ﬁnished using it.

j Use a dry cloth to clean the housing – under

no circumstances use petrol, solvents or clean-

ing agents that attack plastic.

j Pack away the compressed air tacker in the

supplied carrying case after each use to

protect it from dirt.

Service

WARNING!

Have your fastener

driving tool repaired only by qualified

specialist personnel using original

manufacturer parts only. This will ensure

that your fastener driving tool remains safe to use.

Warranty

This appliance is guaranteed for 3 years

from the date of purchase. It has been care-

Operation / Maintenance and cleaning / Service / Warranty

32999_Druckluft-Tacker_Content_LB5 (ohne PT).indd 26 06.07.09 09:53

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside KH 3041 in the language / languages: English, German, Dutch, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside KH 3041 Manual

Product: