679614
14
Zoom out
Zoom in
Previous page
1/33
Next page
14 GB/IE/CY
A tip! Using the device safely.
DANGER! Always guide
the device through the
workpiece against the di-
rection of rotation of the
disc. If you work in the other direction there is
the risk of kickback. The device may be forced
out of the cut.
Always switch on the device before
placing it against the workpiece. After
cutting or grinding, always lift the device from
the workpiece before switching it off.
When working always hold the device
securely with both hands (see Fig. D).
Always keep proper footing and balance.
For the best grinding performance move the
device evenly to and fro over the workpiece
maintaining an angle of 15° to 30° (between
grinding disc and workpiece).
When working on inclined surfaces do
not press the device hard down on to
the workpiece. If the speed slows greatly,
use less pressure. This will allow you to work
more effectively and safely. If the device sudden-
ly stops due to it becoming retarded or trapped,
pull the mains plug from the socket immediately.
Cutting: Advance the device at an
appropriate rate. Do not incline the
cutting disc.
Roughing, grinding and cutting discs
get hot during use – allow them to
cool fully before touching them.
Never use the device for a purpose
for which it was not intended.
Before you insert the mains plug into
the socket, always check that the de-
vice is switched off.
If a dangerous situation arises, pull
the mains plug immediately out of the
mains socket. Ensure that the device and
the mains plug are easily accessible and can
be reached quickly in an emergency.
When taking a break from your
work, before carrying out any tasks
on the device itself and when you are
not using the device, always pull the
mains plug out of the mains socket.
Always keep the device clean, dry and free of
oil or grease.
Remain alert at all times! Always watch
what you are doing and proceed with
caution. Do not use the device if you cannot
concentrate or you are feeling unwell.
Preparing for use
Attaching the disc guard cover
using the quick-release fastener
WARNING!
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
DANGER OF INJURY! Always use the
angle grinder with the disc guard
cover in place. The disc guard cover must
be securely attached to the angle grinder. To
ensure the highest level of safety while using
the device, ensure that the smallest possible
area of the grinding or cutting tool is exposed
to the operator at all times. The disc guard cov-
er is there to protect the operator from pieces
breaking off and accidental contact with the
grinding or cutting tool.
DANGER OF INJURY! Ensure that the
guard
7
is attached so that its edge
is beyond the angle of the auxiliary
handle
6
(see Fig. B). Otherwise you
could injure yourself against the grinding or
cutting disc.
Open the clamping lever
8
.
Insert the disc cover guide
7
with the coded
projection
9
in the coded groove
16
.
Turn the disc guard cover
7
into the desired
position (working position). The closed side of
the disc guard cover
7
must always be facing
the operator.
Close the clamping lever
8
to firmly clamp
the disc guard cover
7
in place.
If necessary the clamping force of the connection
can be adjusted by tightening or loosening the
adjuster screw
10
.
General safety advice for electrical power tools / Preparing for use
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside KH 3039 - PWS 230 SE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside KH 3039 - PWS 230 SE in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside KH 3039 - PWS 230 SE

Parkside KH 3039 - PWS 230 SE User Manual - German, Dutch, French - 47 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info