679614

Parkside KH 3039 - PWS 230 SE Manual

11
Zoom out
Zoom in
Previous page
1/33
Next page
11 GB/IE/CY
General safety advice for electrical power tools
avoid the attachment bouncing or
snagging on the workpiece. Corners,
sharp edges or bouncing have a ten-
dency to snag the rotating attachment.
This causes loss of control or kickback.
e) Do not use saw-chain woodcarving
discs or toothed discs. Such attachments
create frequent kickback and loss of control of
the electrical power tool.
Special safety advice relating
to grinding and disc-cutting
a) Always use the guard designed for
the type of abrasive consumable you
are using. Always use abrasive consumables
approved for use with your electrical power
tool. Abrasive consumables not approved for
use with your electrical power tool cannot be
adequately guarded and are unsafe.
b) To ensure the highest level of opera-
tional safety, the disc guard cover
must be attached to the electrical
power tool and set in such a way that
the smallest possible area of the
abrasive consumable is exposed to
the operator. The disc guard cover is there
to protect the operator from pieces breaking
off and accidental contact with the abrasive
consumable.
c) Abrasive consumables must be used
only for their recommended purpos-
es, For example: never grind with the
side face of a cutting disc. Cutting discs
are intended for removing material using the
edge of the disc. Sideways forces on these
abrasive consumables can cause them to break.
d) Always use an undamaged mounting
flange of the correct size and shape
for your selected grinding disc. Suitable
flanges support the grinding disc and reduce
the chance of it breaking. Flanges for cutting
discs are different from the flanges for other
abrasive discs.
e) Never use worn down abrasive con-
sumables intended for larger electrical
power tools. Abrasive consumables intended
for larger electrical power tools are not designed
for the faster rotational speeds of these smaller
electrical power tools and could break.
Further special safety
advice for disc-cutting
a) Avoid snagging the cutting disc and
do not use too much contact pressure.
Do not attempt to make excessively
deep cuts. Overloading the cutting disc in-
creases the load and the tendency of the disc
to twist or snag in the cut, making kickback or
disc breakage more likely.
b) Avoid the area in front of or behind
the rotating cutting disc. If the cutting disc
is moving away from you at the point of con-
straint in the workpiece, then, in the event of
a kickback, the electrical power tool and the
rotating disc may be thrown towards you.
c) If the cutting disc jams or you stop
work for a while, switch the device
off and hold it until the disc comes to
a complete stop. Never attempt to
pull the still rotating cutting disc out of
the cut as this could cause kickback.
Determine and rectify the reason for the jamming.
d) Do not switch on the device if the cut-
ting disc is in the workpiece. Allow the
cutting disc to reach full speed before carefully
continuing with the cut. Otherwise the disc
could snag, jump out of the workpiece or
cause a kickback.
e) Support boards or workpieces whilst
cutting to reduce the risk of kickback
caused by a jammed cutting disc. Large
workpieces may bend under their own weight.
The workpiece must be supported to both sides
of the cutting disc and particularly near the
cutting disc and at the workpiece edge.
f) Be particularly careful when pocket
cutting in existing walls or other areas
where you cannot see what you are
cutting into. The cutting disc plunged into
the surface could cut through gas or water
pipes, electricity cables or other objects and
cause kickback.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside KH 3039 - PWS 230 SE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside KH 3039 - PWS 230 SE in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside KH 3039 - PWS 230 SE

Parkside KH 3039 - PWS 230 SE User Manual - German, Dutch, French - 47 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info