464953
9
Zoom out
Zoom in
Previous page
1/13
Next page
9 GB/IE/CY
suitably qualified person or at the Customer
Service Centre.
J Always work with the mains lead leading
away from the rear of the device.
J If a dangerous situation arises, pull the mains
plug immediately out of the mains socket.
J Always switch on the electrical power tool before
moving the workpiece against it. Otherwise
there is the risk of kickback.
J Do not cut moist materials or damp surfaces,
J Use only undamaged, defect-free saw blades
7
.
Distorted or blunt saw blades
7
can break or
cause a kickback.
J Ensure that the teeth on the saw blade
7
point
downwards before you mount it in the device.
J DANGER OF INJURY! Keep your hands
away from the area of the saw blade.
J Before sawing, check the workpiece for foreign
bodies such as nails etc. and remove them. In-
jury and / or damage to property may result from
the saw blade striking nails etc. embedded in
the workpiece.
J Always keep the device clean, dry and free
from oil or grease.
J Switch off the device before you remove any
wood residue from around the saw blade.
Otherwise you could become injured.
WARNING!
HAZARDOUS DUSTS /
VAPOURS! Any noxious dusts or vapours
generated from sawing represent a risk to the
health of the person operating the device and
to anyone near the work area.
J Do not saw materials containing substances
harmful to health.
J Do not use the tool on materials containing
asbestos. Asbestos is a known carcinogen.
J Make sure you have adequate ventilation.
J Wear protective glasses, hearing
protection, dust protection masks
and protective gloves.
Q
Advice on use
J Push the workpiece slowly and with minimum
pressure on to the saw blade.
J Reduce the rate of advance when you are
cutting thicker material.
J Hold the workpiece firmly on the table with
both hands and push it slowly towards the saw
blade. Otherwise the saw blade may twist or
break.
J Avoid making any sharp changes in direction
during sawing to prevent the saw blade from
twisting or tearing.
J Before starting the saw cut, drill a hole at a
corner or internal cut-out in the workpiece and
start sawing from the hole.
J Use the correct saw blade. The choice of saw
blade depends on the thickness and type of
material and the intended cut.
Select a saw blade with fine teeth to saw thin,
hard materials.
Use a narrow saw blade to saw small radius
cuts.
Q
Assembly
WARNING!
DANGER OF INJURY!
Pull the mains plug out of the socket before you
carry out any task on the device,
Q
Attaching the blade guard
9
(see Fig. A)
j Push the screw
10 c
from the inside through the
slot in the blade guard
9
.
j From the outside of the blade guard
9
, place
the guide plate
10 b
on to the screw
10 c
.
The bent-up side of the guide plate
10 b
engages
around the blade guard
9
.
j Attach the blade guard
9
between the two at-
tachment arms
11
and insert the two screws
10 c
through the openings provided for them in the
attachment arms
11
.
j Ensure that the upwardly curved end of the
blade guard
9
is at the top.
j Put the plain washers
10 a
on from the outside
of the attachment arms
11
.
j Screw the knurled nuts
10
on to the two screw
ends
10 c
.
j Slide the blade guard
9
into the desired posi-
tion and fix it in that position by tightening the
knurled nuts
10
.
Safety advice / Assembly
33383_SCROLL SAW_Dekupiersaege_Content_LB6.indd 9 23.07.09 11:29
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside KH 3038 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside KH 3038 in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside KH 3038

Parkside KH 3038 User Manual - German, Dutch, French - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info