745187
55
Zoom out
Zoom in
Previous page
1/80
Next page
55
MTGB
red-yellow-green =Battery fully charged
red and yellow =Battery half charged
red =Battery needs to be charged
Operation
1. Choice of gear
Slide the gear selector
(
4) to LO or HI, corresponding to a low
or high torque selection.
A gear change may only be
performed in standstill mode!
2. Direction switch
You can toggle between right and left ro-
tation by pushing the direction of rotation
switch (
5).
If you move the direction switch (
5) to
the middle position, the device is secured
against being switched on.
The direction changed may
only be performed in stand-
still mode!
3. Torque adjustment
You can preset the maximum torque by
rotating the torque adjustment ring (
3)
17+1 torque levels are provided. At the
last level, the maximum torque is available.
This position is especially suitable for dril-
ling, so it is also marked with a drill icon.
Reaching the preset torque limit produces
a noticeable rasping sound. This sound is
caused by the slip clutch.
Torque adjustment should
only be performed in stand-
still mode!
4. Keyless drill chuck
removal
To use the bitholder (17), you must remove
the keyless chuck (1).
Hold the keyless chuck (1) rmly from the
front and pull or push the Chuck ring (2)
against the keyless chuck (1) in the direc-
tion of the arrow mark „Unlock“ on the
Chuck ring (2). This unlocks the keyless
chuck (1) and it can be pulled forward.
To set the keyless chuck again, pull it onto
the bitholder (17) until you can push it over
completely. Lock the keyless chuck (1) with
the Chuck ring (2). To do this, push or pull
the Chuck ring (2) in the direction of the
arrow mark „Lock“ on the Chuck ring (2).
5. Tool change
Rotate the keyless chuck (1) counter-clock-
wise, until the drill chuck aperture is large
enough to accommodate the tool.
Push the tool as far as possible into the
keyless chuck (1) and rotate the chuck
clockwise to clamp the tool rmly.
To remove the tool again, rotate the keyless
chuck (1) and pull out the tool.
6. Using the bitholder
After removing the keyless chuck (1) you can
use the bitholder.
Insert a suitable 6-point bit in the bitholder
(17). Because of the 6-point bit holder, it may
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 96229 PABSW 10.8 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 96229 PABSW 10.8 B2 in the language / languages: Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 96229 PABSW 10.8 B2

Parkside IAN 96229 PABSW 10.8 B2 User Manual - English, German, Dutch - 52 pages

Parkside IAN 96229 PABSW 10.8 B2 User Manual - French - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info