745201

Parkside IAN 93548 PMNF 1350 A1 Manual

31
Zoom out
Zoom in
Previous page
1/34
Next page
31 GB
General power tool safety warnings / Start-up / OperationGeneral power tool safety warnings
Original accessories / tools
Use only the accessories and attachments de-
tailed in the operating instructions, or those which
are compatible with the device.
Start-up
Setting the groove depth
Loosen set screw
6
.
Set the depth stop
7
to the desired depth.
Tighten set screw
6
.
Installing the dust
extraction adapter
Slide the pegs of the extraction adapter
3
into the slots of the dust extraction connection.
Turn the extraction adapter
3
to lock.
Loosen union nut
3 a
.
Insert the tube of the extraction unit far enough
into the opening on the union nut
3 a
.
Tighten union nut
3 a
.
Operation
Switching ON / OFF
NOTE: Always switch on the device before bringing
into contact with the material and only then apply
the device to the work piece. The wall grinder fea-
tures electronic smooth start-up. The motor‘s start-up
is delayed.
Switching the unit on:
Activate the switch lock
9
(see Fig. C). Then
press the ON / OFF switch
1
.
Switching the device off:
Release the ON / OFF switch
1
.
Installing and adjusting
the cutting width of the
diamond cutting discs
Loosen set screw
6
.
Slide the depth stop
7
up.
Press and hold the spindle lock
10
.
Use the face pin wrench
15
to loosen the
adapter flange
5
.
Remove the adapter flange
5
.
Set the desired cutting width with the number
of spacers
14
. Be sure to use the centring
flange
13
as the top spacer.
NOTE: You may choose from various spacers.
Please note, the total number of spacers betw
een
the cutting discs and the thickness of the cutting
discs yield the groove width.
Tighten the adapter flange with the face pin
wrench
15
. When doing so, hold the spindle
lock.
NOTE: When setting a cutting width smaller
than the maximum, you must use the spacers
on the clamping collar side, as the clamping
collar alone cannot secure the discs due to the
thread length on the spindle (see. Fig. D).
NOTE: Always replace diamond cutting discs
in pairs.
Handling the wall chaser
(see Fig. E)
ATTENTION! This device is only suitable for
dry cuts!
Use a cable detector to check walls for hidden
electrical-, gas- and water lines before using
the wall chaser.
Select the desired groove width.
Apply the roller
11
of the device onto the brick
wall.
Now switch on the device and immerse into
the brick wall until the depth stop
7
touches.
Now cut the groove into the brick wall, noting
the cutting direction. The device must be rotat-
ing in the opposite direction. The device can
otherwise erratically be pushed out of the cut.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 93548 PMNF 1350 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 93548 PMNF 1350 A1 in the language / languages: French as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 93548 PMNF 1350 A1

Parkside IAN 93548 PMNF 1350 A1 User Manual - English, German, Dutch - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info