Manual Parkside IAN 93548 PMNF 1350 A1 (page 29 of 34) (English, German, Dutch)

745201

Zoom out

Zoom in

1/34

29 GB

General power tool safety warningsGeneral power tool safety warnings

marked on the power tool. Accessories

running faster than their rated speed can break

and ﬂy apart.

d) Wheels must be used only for recom-

mended applications. For example:

do not grind with the side of cut-off

wheel. Abrasive cut-oﬀ wheels are intended

for peripheral grinding, side forces applied to

these wheels may cause them to shatter.

e) Always use undamaged wheel flanges

that are of correct diameter for your

selected wheel. Proper wheel ﬂanges sup-

port the wheel thus reducing the possibility of

wheel breakage.

f) Do not use worn down reinforced

wheels from larger power tools. Wheels

intended for a larger power tool are not suita-

ble for the higher speed of a smaller tool and

may burst.

g) The outside diameter and the thickness

of your accessory must be within the

capacity rating of your power tool. In-

correctly sized accessories cannot be adequately

guarded or controlled.

h) The arbour size of wheels and flanges

must properly fit the spindle of the

power tool. Wheels and ﬂanges with arbour

holes that do not match the mounting hardware

of the power tool will run out of balance, vibrate

excessively and may cause loss of control.

i) Do not use damaged wheels. Before

each use, inspect the wheels for chips

and cracks. If power tool or wheel is

dropped, inspect for damage or install

an undamaged wheel. After inspecting

and installing the wheel, position your-

self and bystanders away from the

plane of the rotating wheel and run

the power tool at maximum no load

speed for one minute. Damaged wheels

will normally break apart during this test time.

j) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasse

As appropriate, wear dust mask, hear-

ing protectors, gloves and shop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection

must be cap-able of stopping ﬂying debris gen-

erated by various operations. The dust mask

or respirator must be capable of ﬁltrating par-

ticles generated by your operation. Prolonged

exposure to high intensity noise may cause

hearing loss.

k) Keep bystanders a safe distance away

from work area. Anyone entering the

work area must wear personal protec-

tive equipment. Fragments of workpiece or

of a broken wheel may ﬂy away and cause in-

jury beyond immediate area of operation.

l) Hold the power tool by insulated grip-

ping surfaces only, when performing

an operation where the cutting acces-

sory may contact hidden wiring or its

own cord. Cutting accessory contacting a

“live” wire may make exposed metal parts of

the power tool “live” and could give the oper-

ator an electric shock.

m) Position the cord clear of the spinning

accessory. If you lose control, the cord may

be cut or snagged and your hand or arm may

be pulled into the spinning wheel.

n) Never lay the power tool down until

the accessory has come to a complete

stop. The spinning wheel may grab the surface

and pull the power tool out of your control.

o) Do not run the power tool while car-

rying it at your side. Accidental contact

with the spinning accessory could snag your

clothing, pulling the accessory into your body.

p) Regularly clean the power tool’s air

vents. The motor’s fan will draw the dust inside

the housing and excessive accumulation of

powdered metal may cause electrical hazards.

q) Do not operate the power tool near

flammable materials. Sparks could ignite

these materials.

r) Do not use accessories that require

liquid coolants. Using water or other liquid

coolants may result in electrocution or shock.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 93548 PMNF 1350 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 93548 PMNF 1350 A1

Parkside IAN 93548 PMNF 1350 A1 User Manual - French - 34 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 93548 PMNF 1350 A1 Manual

Product: