745195

Parkside IAN 93523 PWS 125 A1 Manual

14
Zoom out
Zoom in
Previous page
1/108
Next page
14 GB/IE
Use / Use of accessoriesGeneral safety advice for electrical power tools / Use
For the best grinding performance move the
device evenly to and fro over the workpiece
maintaining an angle of 15° to 30° (between
grinding disc and workpiece).
When working on inclined surfaces do
not press the device hard down on to
the workpiece. If the speed slows greatly,
use less pressure. This will allow you to work m
ore
effectively and safely. If the device suddenly
stops due to it becoming retarded or trapped,
pull the mains plug from the socket immediately.
Cutting: Advance the device at an
appropriate rate. Do not incline the
cutting disc.
Roughing, grinding and cutting discs
get hot during use – allow them to
cool fully before touching them.
Never use the device for a purpose
for which it was not intended.
Before you insert the mains plug into
the socket, always check that the de-
vice is switched off.
If a dangerous situation arises, pull
the mains plug immediately out of the
mains socket. Ensure that the device and
the mains plug are easily accessible and can
be reached quickly in an emergency.
When taking a break from your
work, before carrying out any tasks
on the device itself and when you are
not using the device, always pull the
mains plug out of the mains socket.
Always keep the device clean, dry and free of
oil or grease.
Remain alert at all times! Always watch
what you are doing and proceed with
caution. Do not use the device if you cannot
concentrate or you are feeling unwell.
Q
Use
Q
Switching on and off
Check the attached consumable or tool before use.
It must be attached properly, not damaged, damp
or cracked and must rotate freely. Test the operation
of the device for 30 seconds. If a disc is not round
or vibrates, do not use it. Look out for unusual noises
or generation of sparks. Check that all the fastenings
are correctly attached.
Switching on:
Press the safety lock-out
1
.
Press the ON / OFF switch
2
.
Switching off:
Release the ON / OFF switch
2
again.
Q
Setting the speed
Select the desired speed before use to suit your
purpose. Turn the speed preselector wheel
10
to the desired setting. The required rotational
speed depends on the material being worked
and the working conditions and can be deter-
mined by means of a practical test.
The table below shows some recommended
settings (for guidance only and given without
liability) for a number of common applications.
The accessories mentioned may not all be sup-
plied as standard with the product.
Preselected rotation speed:
Material
Application
Tool Setting
Plastic,
varnish
Polishing Lambswool
bonnet
1
Fine finish
Felt polishing
disc
1
Metal Fine finish Buffing disc 1
Paint
removal
Sanding sheet 2–3
Wood,
metal
Brushing,
derusting
Cup brush,
sanding sheet
3
Metal Grinding /
abrading
Grinding disc 4–6
Metal Roughing /
grinding
Roughing /
grinding disk
6
Metal Cutting Cutting disc 6
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 93523 PWS 125 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 93523 PWS 125 A1 in the language / languages: English, German, Dutch, Danish, French, Swedish as an attachment in your email.

The manual is 6,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info