745196
48
Zoom out
Zoom in
Previous page
1/51
Next page
48 GB
Use of accessories / Maintenance and cleaning
Note! These may only be used in combination
with a backing plate!
Cup brush, crimped wire
Dimensions: ø 75–100 mm
Speed: min. 12000 rpm
Cup brush, twisted wire
Dimensions: ø 75 mm
Speed: min. 12000 rpm
Cup brush, knotted wire
Dimensions: ø 115 mm
Speed: min. 12000 rpm
Q
Adjusting the disc guard cover
DANGER OF INJURY!
Pull the mains plug out of the mains socket
before you carry out any task on the device.
In order to adjust the safety cover
5
, one does
not need to remove the screws
12
but just loo-
sen them.
12
5
DANGER OF INJURY! Always use the an-
gle grinder with the disc guard cover
5
in
place. The disc guard cover must be securely
attached to the angle grinder. To ensure the
highest level of safety while using the device,
ensure that the smallest possible area of the
grinding or cutting tool is exposed to the oper-
ator at all times (see Fig. C, D). The disc guard
cover
5
is there to protect the operator from
pieces breaking off and accidental contact
with the grinding or cutting tool. The disc guard
cover has 5 set positions.
Turn the disc guard cover
5
into the desired
position (working position).
The closed side of the disc guard cover
5
must
always be facing the operator.
Q
Using the auxiliary handle
CAUTION! For safety reasons this device must
always be used with the auxiliary handle
4
in
place.
The auxiliary handle
4
can be screwed on to the
left, right or on the top of the head of the device.
Q
Maintenance and cleaning
DANGER OF INJURY!
Pull the mains plug out of the mains socket
before you carry out any task on the device.
Do not use sharp objects for cleaning
the device. Do not allow any liquids
to enter the device. Otherwise the tool may
be damaged.
Have the carbon brushes replaced only at the
service centre or an accredited electrical
equipment repair centre. The device requires
no other maintenance.
Maintenance and cleaning / Service / Warranty / Disposal
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 90983 PWS 125 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 90983 PWS 125 A1 in the language / languages: French as an attachment in your email.

The manual is 3,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 90983 PWS 125 A1

Parkside IAN 90983 PWS 125 A1 User Manual - English, German, Dutch - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info