745196
43
Zoom out
Zoom in
Previous page
1/49
Next page
43 GB
General safety advice for electrical power toolsGeneral safety advice for electrical power tools
For safety reasons this device must
always be used with the auxiliary
handle
4
in place.
The adjustable disc guard cover
5
must
always be in place when working with
roughing, grinding or cutting discs.
Otherwise there could be danger of injury.
Use the vacuum dust extraction facility
if your work generates high amounts
of dust. Use suction devices particular-
ly approved for the purpose.
Use permitted consumables and tools
only. Check that the speed given on the
discs is greater or equal to the rated
speed of the device.
Take note of the direction of rotation
and always hold the device in such a
way that the sparks and grinding de-
bris are thrown away from your body.
Otherwise there could be danger of injury.
Make sure that the dimensions of the
disc are suitable for the device and
that the disc is of a type that fits prop-
erly on to the mounting flange
8
.
Q
Advice on use
Note! Discs must be used only for their recom-
mended purposes, otherwise they could disintegrate,
become damaged or cause accidents.
Roughing (see Fig. G):
Never use cutting discs for
roughing or grinding!
Move the angle grinder using even
pressure to and fro over the workpiece.
Hold the roughing or grinding disc at
a flat angle to the workpiece when
working on a soft material. Use a
slightly steeper angle for harder ma-
terials.
Disc-cutting (see Figs. E, F):
Never use roughing or
grinding discs for cutting!
Only use certified fibre-reinforced cut-
ting or grinding discs approved for use at
circumferential speeds of not less than 80 m / s.
CAUTION! The disc continues to rotate after
the device has been switched off. Do not at-
tempt to slow it down by pressing on the side
of the disc.
Securely support the workpiece. Use
clamps or a vice to grip the workpiece firmly.
This is much safer than holding it in your hand.
Switch the device off and allow it to
come to a complete standstill before
you put it down.
Unlock the ON / OFF switch immedi-
ately if a power failure occurs or the
plug is pulled out of the mains socket.
Place the switch in the OFF position.
This prevents the device from being inadvertent-
ly started up again.
Use the device for dry cutting or dry
grinding only.
The auxiliary handle
4
must be in
place
whenever the device is being used.
Do not work on materials containing
asbestos. Asbestos is a known carcinogen.
A tip! Using the device safely.
DANGER! Always guide
the device through the
workpiece against the di-
rection of rotation of the
disc. If you work in the other direction there is
the risk of kickback. The device may be forced
out of the cut.
Always switch on the device before
placing it against the workpiece. After
cutting or grinding, always lift the device from
the workpiece before switching it off.
When working always hold the device
securely with both hands (see Fig. G).
Always keep proper footing and balance.
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 90983 PWS 125 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 90983 PWS 125 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 90983 PWS 125 A1

Parkside IAN 90983 PWS 125 A1 User Manual - French - 51 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info