745103
59
Zoom out
Zoom in
Previous page
1/62
Next page
59 GB
Q
Attaching and replacing
roughing / grinding / cutting discs
Take note of the dimensions of the roughing /
grinding or cutting discs. The circular hole must fit
on to the mounting flange without play. Do not use
a reducer piece or adapter.
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
Check the condition of the roughing /
grinding or cutting discs. They must be
free of damage, moisture or cracks.
Otherwise they could break up during use and
cause injury.
DANGER OF BURNS! Always wear
protective gloves when changing a
roughing / grinding or cutting disc.
Roughing / grinding and cutting discs become
hot during use. Do not touch them until after
they have cooled down.
NOTE: Always ensure the discs are free of dirt
before use.
Use only abrasive consumables or tools with
an allowable speed at least as high as the
no-load speed of the device.
DANGER OF INJURY! Press the spindle lock
button
11
only after the mounting spindle
14
has reached a standstill.
Press the spindle lock button
11
to block the drive.
Release the clamping nut
13
using the spanner
17
(see Fig. C).
Place the roughing / grinding or cutting disc on
to the mounting flange
15
with its labelled side
facing towards the device.
Then replace the clamping nut
13
, with its
raised side facing upwards, on to the mounting
spindle
14
.
Press the spindle lock button
11
to block the drive.
Tighten the clamping nut
13
again with the
spanner
17
.
NOTE: Replace a new disc immediately if it
runs unevenly or vibrates after being exchanged.
After replacing a disc let the device run under
no-load conditions for 30 seconds as a safety
check. Look out for unusual noises or generation
of sparks. Check that all the fastened-on parts
are correctly attached.
Pay attention to see that the arrow showing the
direction of rotation on the roughing / grinding
or cutting discs (including diamond cutting discs)
corresponds with the direction of rotation of the
device (see arrow on the head of the device).
Q
Operation
Q
Switching on and off
Note: Always switch on the angle grinder before
bringing it into contact with the workpiece material.
Switching on the device:
Press the safety lock-out
3
(see Fig. H).
Then press the ON / OFF switch
2
.
Switching off the device:
Release the ON / OFF switch
2
.
Rotating the hand grip:
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
The hand grip
1
can be rotated by 90° to
the right or left (see Fig. A).
This allows the ON / OFF switch
2
to be
brought into the most comfortable position for
any working conditions.
Press the unlocking button
4
and rotate the
hand grip
1
to the right or left.
Make sure the hand grip
1
engages.
Q
Maintenance and cleaning
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
Do not use sharp objects for cleaning
the device. Do not allow any liquids
to enter the device. Otherwise the device
could be damaged.
Preparing for use / Operation / Maintenance and cleaningGeneral safety advice for electrical power tools / Preparing for use
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 86738 PWS 230 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 86738 PWS 230 A1 in the language / languages: French, Italian as an attachment in your email.

The manual is 2,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 86738 PWS 230 A1

Parkside IAN 86738 PWS 230 A1 User Manual - English, German, Dutch - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info