745088
29
Zoom out
Zoom in
Previous page
1/33
Next page
29 GB
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this par-
ticular type of device. In doing this, take
into account the working conditions
and the task in hand. The use of electrical
power tools for purposes other than those in-
tended can lead to dangerous situations.
5. Service
a) Have your device repaired at the ser-
vice centre or by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
Safety advice relating spe-
cifically to delta sanders
Securely support the workpiece. Use clamps or
a vice to grip the workpiece firmly. This is much
safer than holding it in your hand.
Never support yourself by placing your hands
near or in front of the device or the workpiece
surface. A slip can result in injury.
If a dangerous situation arises, pull the mains
plug immediately out of the mains socket.
Always work with the mains lead leading
away from the rear of the device.
DANGER OF FIRE FROM FLYING
SPARKS!
Abrading metal creates flying sparks. For this
reason, always make sure that nobody is placed
in any danger and that there are no inflammable
materials near the working area.
NOXIOUS FUMES!
Any harmful / noxious dusts generated from
sanding represent a risk to the health of the
person operating the device and to anyone
near the work area.
Wear protective glasses and a
dust mask!
When sanding wood and in particular when work-
ing on materials that give rise to dusts that are
hazardous to health, the sander must be connect-
ed to a suitable external dust extraction device.
Ensure that there is adequate ventilation when
working on plastic, paint, varnish etc.
Do not soak the materials or the surface you
are about to work on with liquids containing
solvents.
Do not abrade moistened materials or damp
surfaces.
Avoid sanding paints containing lead or other
substances hazardous to health.
Do not work on materials containing asbestos.
Asbestos is a known carcinogen.
Avoid contact with the moving sanding sheet.
Operate the device only with an attached
sanding sheet.
Never use the device for a purpose for which it
was not intended nor with non-original parts /
accessories. The use of tools or accessories other
than those recommended in the operating in-
structions could lead to you suffering an injury.
Switch the device off and allow it to come to a
standstill before you put it down.
Always keep the device clean, dry and free of
oil or grease.
Q
Have you understood
everything?
Once you have made yourself familiar with the
instructions and advice, the functioning and
handling of your device, you are finally in a
position to start work. Observing the manufac-
turer‘s instructions and advice will maximise
your safety while working with the device.
Q
Preparing for use
CAUTION! Make sure that the device is
switched off before you connect it to the mains
supply.
General safety advice for electrical power tools General safety advice for electrical power tools / Preparing for use
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 86059 PDS 290 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 86059 PDS 290 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 86059 PDS 290 A1

Parkside IAN 86059 PDS 290 A1 User Manual - French - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info