745118
41
Zoom out
Zoom in
Previous page
1/44
Next page
41 GB
To switch off continuous operation mode:
j Press the ON / OFF switch
3
and release it
again.
Q
Guiding the sabre saw
safely and accurately
The shoe
5
pivots to adjust to the workpiece and
provides safe support to the device. It must always
lie against the workpiece when the device is in use.
Q
Advice about ways of
working when sawing
J Before sawing, check the workpiece for foreign
bodies such as nails, screws etc. and remove
them.
J Do not allow the ventilation slots to become
covered.
J Switch the device on first and only then bring it
into contact with the workpiece.
J If the saw blade jams, switch off the device im-
mediately.
Open the sawn gap in the workpiece slightly
using a suitable tool and extract the saw blade.
j Always make sure the saw blade type and the
blade oscillation speed are suitable for the
workpiece material.
j There are different saw blades available in var-
ious lengths designed to ensure optimum perfor-
mance of every sawing task with your sabre saw.
j Saw the material using a steady forward rate
of progress.
Flush sawing:
Using flexible saw blades of adequate length you
can trim off projecting workpieces, such as pipes,
directly at the face of a wall.
Follow these steps:
1. Place the saw blade directly on the wall surface.
2. Bend the blade by applying sideways pressure
so that the shoe
5
comes up against the wall.
3. Switch on the device as described above and
trim the workpiece using constant pressure.
Plunge sawing:
CAUTION! DANGER OF KICKBACK!
Plunge sawing can be used only in soft materials
(such as wood etc.).
Follow these steps:
1. Place the sabre saw with the underside of the
shoe
5
against the workpiece.
Switch on the device.
2. Tilt the sabre saw forward and plunge the saw
blade into the workpiece.
3. Bring the sabre saw vertical and continue saw-
ing along the cutting line.
Note: The saw blade used for this should not be
longer than 152 mm!
Q
Maintenance and cleaning
J Pull the mains lead out of the mains socket
before you clean the device.
J Replace the saw blade as soon as its teeth be-
come blunt and it starts to produce defective
saw cuts.
J Always keep the device and the ventilation
slots clean.
j Clean the device after you have finished using it.
j Do not allow any liquids to enter the device.
Use a cloth to clean the housing. Never use
petrol, solvents or cleaning agents that might
attack plastic.
j
If necessary, clean out the
saw blade mounting recess
with a thin paintbrush or compressed air.
Q
Service centre
J
Have your device
repaired only by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
J
If the plug or mains
lead needs to be replaced, always
have the replacement carried out by
the manufacturer or its service centre.
Preparing for use / Maintenance and cleaning / Service centreGeneral safety advice for electrical power tools / Before use / Preparing for use
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 85969 PFS 710 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 85969 PFS 710 A1 in the language / languages: French, Italian as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 85969 PFS 710 A1

Parkside IAN 85969 PFS 710 A1 User Manual - English, German, Dutch - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info