745108
31
Zoom out
Zoom in
Previous page
1/34
Next page
31 GB
General safety advice for electrical power tools / Start-upGeneral safety advice for electrical power tools
If you work outside, connect the device to a
residual current (RCD) protective switch with
a maximum 30 mA tripping current. Only use
extension leads approved for outdoor use.
Note: Always hold the mains cable out of the op-
erating range of the machine and move it towards
the back of the machine.
Start-up
Switching on and off
Switching on:
Pull the ON / OFF switch
6
towards the back
(see Fig. A).
Switching off:
Release the ON / OFF switch
6
.
Releasing the plunge blocker
Push the plunge blocker
1
towards the front
and keep it pressed.
Preselect cutting depth
Note: We recommend adjusting the cutting depth
at least 2 mm deeper than the thickness of the ma-
terial. This will result in a clean cut.
Release the quick release of the cutting depth
pre-selector
7
, adjust the desired cutting depth
at the scale
7 a
and refit the quick release.
Fitting the guide fence
Release the screw of the guide fence
11 a
at
the base plate
9
and insert the guide fence
11
into the guide fence fixture
10
. Retighten these
screws
11 a
.
Handling the plunge saw
1. Put the machine onto the material and switch it on
as described in the chapter “Switching on and off”.
2. If necessary adjust the machine to the guide
fence
11
or a drawn line.
3. Hold the machine as shown in Figure A and
cut with light pressure.
Types of saw blades:
The saw blades included cover the most common
types of application.
HW Circular saw blade
20
Z85 / 30:
Description: ø 85 mm, 30 HW-teeth
Suitable for: Soft wood, hard wood, boards of any type
Diamond cutting disc
21
Z85VR:
Description: ø 85 mm, without teeth
Suitable for: Ceramics, plastics
HS Circular saw blade
22
Z85 / 36:
Description: ø 85 mm, 36 teeth – tooth setting
left / right
Suitable for: Soft wood, soft metals such as aluminium,
copper
Marking cutting length
Orient yourself at the markings for the cutting
length
8
, in order to check where your cut
starts and ends.
Marking cutting line
The cutting line viewing window allows precise
guidance of the machine along the cutting line
applied to the workpiece.
In order to achieve an exact cut, place the
machine on the workpiece so that the cutting
length labelling appears in the cutting line
viewing window
12
, as depicted in Illustration B.
79416_par_Tauchsaege_Content_DE-AT-NL.indd 31 07.12.12 12:47
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 79416 PTS 480 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 79416 PTS 480 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 79416 PTS 480 A1

Parkside IAN 79416 PTS 480 A1 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info