Manual Parkside IAN 75908 PWS 125 A1 (page 60 of 67) (English, German, Dutch, French)

744961

Zoom out

Zoom in

1/67

60 GB

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow

the cutting disc to reach full speed be-

fore carefully continuing with the cut.

Otherwise the disc could snag, jump out of the

workpiece or cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) B

e particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are cut-

ing into. The cutting disc plunged into the surface

could cut through gas or water pipes, electricity

cables or other objects and cause kickback.

Special safety advice for

abrading using sandpaper

Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming,

tearing of the sheet or kickback.

Special safety

advice for polishing

Do not use the polishing bonnet if it

has any loose parts, in particular the

fastening cords. Tuck the fastening cords

away or trim them. Loose fastening cords rotat-

ing with the attachment could catch your ﬁngers

or become trapped in the workpiece.

Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b) U

se a guard, if recommended, but m

ake

sure that the wire brush does not come

into contact with the guard. The diameters

of disc brushes and cup brushes can increase

due to contact pressure and centripetal forces.

Safety advice

for angle grinders

DANGER OF ELECTRIC SHOCK! Do not

operate the device if the mains lead

or mains plug is damaged.

DANGER OF ELECTRIC SHOCK! Do not

touch the mains lead if it becomes

damaged or cut through while you

are using the device. Pull the plug out of

the mains socket immediately and have the de-

vice repaired by a suitably qualiﬁed person or

at your service centre.

DANGER OF ELECTRIC SHOCK! Do not

operate the device if it is damp and

do not use it in a damp environment.

DANGER OF ELECTRIC SHOCK! If you

use the device outdoors, always con

nect

it through a residual current device

(RCD) with a maximum trip current of

30 mA. If using an extension lead, always use

one that is approved for outdoor use.

Do not suspend or carry the device by

the mains lead. Always work with the

mains lead leading away from the

rear of the device. Otherwise the device

could be damaged.

Grinding discs must be carefully kept

and handled in accordance with the

manufacturer’s instructions. Otherwise

they could be damaged.

Make sure that abrasive consumables

and tools are attached in accordance

with the manufacturer’s instructions

and advice. Otherwise they could become

detached from the device and result in injury

and / or damage to property.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 75908 PWS 125 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 75908 PWS 125 A1 Manual

Product: