744943
47
Zoom out
Zoom in
Previous page
1/52
Next page
47 GB
Before first use General safety advice for electrical power tools / Before first use
Note! A new battery pack, or one that has not
been in use for an extended period, must be charged
up before the first / renewed usage.
The battery pack attains its full capacity after ca.
3–5 charging cycles.
CAUTION! Always ensure the plug is removed
from the mains socket before inserting a battery pack
into, or removing one from, the charging station.
Never charge the battery pack if the ambient
temperature is less than 10 °C or greater than
40 °C.
1. Insert the battery pack
6
into the quick-
charger
15
(see Fig. C).
2. Insert the mains plug into the mains socket. The
flashing green charge indicator LED
17
shows
that charging is in progress.
3. The charging process is completed when the
green charge indicator LED
17
light up and the
accumulator pack
6
is ready for operation.
4. If the red charge indicator LED
16
lights up, the
quick battery charger
15
is in standby mode;
the accumulator pack
6
is not connected.
5. If the red charge indicator LED
16
starts flas-
hing, this means that the accumulator pack
6
has become too hot; no charging process.
Never charge the battery pack for a second time
immediately after a fast charging process has
been completed. This can give rise to the battery
pack becoming overcharged and to a reduced
service life of the battery and charging station.
Switch the charger off for at least 15 minutes
between two successive charging procedures.
Remove the power plug from the wall socket.
Q
Insertion / removal of a battery
pack into the appliance
Ensure that the appliance is switched off before in-
serting the battery. The insertion of a battery into an
electrical appliance that is switched on can lead to
accidents.
Inserting the rechargeable battery pack:
Move the rotation switch
2
into the middle
position (lock) and push the rechargeable bat-
tery pack
6
into the handle until it engages.
Removing the rechargeable battery pack:
Press the release button
7
and remove the
rechargeable battery pack
Q
Checking battery status
To check the battery status, press the battery
LED button
11
(refer to main diagram). The
status or residual capacity will be indicated in
the battery LED
10
as follows:
GREEN / RED / ORANGE = maximum charge /
capacity
RED / ORANGE = medium charge / capacity
RED = weak charge – recharge battery
Q
Changing tools
Your cordless electric drill / screwdriver has a fully
automatic spindle lock
and is fitted with an
enclosed keyless chuck incorporating the latest
technology from
”Made in Germany”.
Once the motor has come to a halt, the drive shaft
is automatically locked, so that the chuck
13
can
be opened simply by turning it
.
After you have inserted the required bit and fixed it
in place by turning the chuck
, you can immedi-
ately continue working. The spindle lock releases
itself automatically when the motor is started (by
operation of the ON / OFF switch
3
).
Q
Torque pre-selection
You can adjust the torque by using
14
torque pre-
selection. The torque levels regulate a range of up
to ca. 35 Nm.
Select a low setting for small screws, soft work
material.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 75636 PABS 18 Li B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 75636 PABS 18 Li B2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info