745064
53
Zoom out
Zoom in
Previous page
1/57
Next page
53 GB
General safety advice for electrical power tools / Operation
CAUTION! The tool continues to rotate
after it has been switched off!
Avoid contact with rapidly rotating
drill / grinder components.
Securely support the
workpiece. Use clamps or a vice to grip the
workpiece firmly. This is much safer than holding
it in your hand.
Never support your-
self by placing your hands near or in
front of the device or the workpiece
surface. A slip can result in injury.
Avoid contact with moving sanding or
grinding tools.
DANGER OF FIRE FROM FLYING
SPARKS! Abrading metal creates
flying sparks. For this reason, always
make sure that nobody is placed in any danger
and that there are no inflammable materials
near the working area.
DUST HAZARD! Any
harmful / noxious dusts generated from machin-
ing represent a risk to the health of the person
operating the device and to anyone near the
work area.
Wear a dust mask!
NOXIOUS FUMES!
Ensure that there is adequate ventilation when
machining surfaces containing plastic or cov-
ered with paint, varnish etc.
Do not soak the materials or the sur-
face you are about to work on with
liquids containing solvents.
Avoid abrading paints containing lead
or other substances hazardous to
health.
Do not machine materials containing
asbestos. Asbestos is a known carcinogen.
Do not machine moist materials or
damp surfaces.
NOTE! Do not allow the tool to come to a
standstill by overloading it!
Switch the device off
and allow it to come to a standstill be-
fore you put it down.
Always keep the de
vice
clean, dry and free of oil or grease.
Children or persons who lack the knowledge or
experience to use the device or whose physical,
sensory or intellectual capacities are limited
must never be allowed to use the device without
supervision or instruction by a person responsible
for their safety. Children must never be allowed
to play with the device.
Q
Operation
Never use the device for a purpose
for which it was not intended or with
non-original parts / accessories. The use
of tools or accessories other than those recom-
mended in the operating instructions could lead
to you suffering an injury.
Q
Inserting or replacing
a tool / collet
Press the spindle lock
7
and keep it pressed.
Rotate the clamping nut
5
until the lock
engages.
Loosen the clamping nut
5
with the combina-
tion key
23
.
If a tool is already inserted, remove it.
First insert the tool you wish to use though the
clamping nut
5
before you insert it into the
collet
18
suitable for the tool shaft.
Press the spindle lock
7
and keep it pressed.
Insert the collet
18
into the threaded insert and
tighten the clamping nut
5
on the thread using
the combination key
23
.
Using the Insertion tool with mandrel
13
:
NOTE: Use the screwdriver end of the combi-
nation key
23
to release or tighten the screw of
the mandrels
13
.
Insert the mandrel
13
into the electrical tool as
described.
With the aid of the combination wrench
23
,
unscrew the screw from the mandrel
13
.
Place the insertion tool you wish to have onto
the screw between the two washers.
With the aid of the combination wrench
23
,
tighten the screw on the mandrel
13
.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 75273 PMGS 12 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 75273 PMGS 12 B2 in the language / languages: French as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 75273 PMGS 12 B2

Parkside IAN 75273 PMGS 12 B2 User Manual - English, German, Dutch - 45 pages

Parkside IAN 75273 PMGS 12 B2 User Manual - French - 57 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info