Manual Parkside IAN 75273 PMGS 12 B2 (page 39 of 45) (English, German, Dutch)

745064

Zoom out

Zoom in

1/45

39 GB

Safety advice

relating to kickback

Kickback is the sudden reaction to a pinched or

snagged rotating attachment, such as a grinding

disc, grinding pad, wire brush etc. Pinching or

snagging results in the rotating attachment coming

to an abrupt stop. This causes the electrical power

tool (if not controlled) to move in the opposite di-

rection to the direction of rotation of the attachment

at the point of constraint.

If, for example, a grinding disc is pinched or snags

in a workpiece, this can cause the edge of the

grinding disc to penetrate the workpiece, become

trapped there and either free itself or kickback. The

grinding disc moves towards or away from the op-

erator, depending on the direction of movement of

the disc at the point of constraint. The grinding disc

could also break.

Kickback occurs as a result of incorrect use or misuse

of the electrical power tool. It can be prevented by

taking the appropriate precautions as described below.

a) Maintain a firm grip on the electrical

power tool and position your body

and arms to allow you to resist kick-

back forces. Always use the auxiliary

handle, if provided, to exercise the

greatest possible control over kick-

back forces or reaction torques as the

device builds up to full speed. By taking

suitable precautions the operator can control

kickback and reaction forces.

b) Do not place your hands near a rotat-

ing attachment. If kickback occurs the at-

tachment could move over your hand.

c) Avoid positioning your body in the

area into which the electrical power

tool would move in the event of a

kickback. A kickback moves the electrical

power tool in the opposite direction to the di-

rection of movement of the grinding disc at the

point of constraint.

d) Work particularly carefully in the

area of corners, sharp edges etc. to

avoid the attachment bouncing or

snagging on the workpiece. Corners,

sharp edges or bouncing have a tendency to

snag the rotating attachment. This causes loss

of control or kickback.

e) Do not use saw-chain woodcarving

discs or toothed discs. Such attachments

create frequent kickback and loss of control of

the electrical power tool.

Special safety advice relating

to grinding and disc-cutting

a) Always use the guard designed for

the type of abrasive consumable you

are using. Always use abrasive consumables

approved for use with your electrical power

tool. Abrasive consumables not approved for

use with your electrical power tool cannot be

adequately guarded and are unsafe.

b) To ensure the highest level of opera-

tional safety, the disc guard cover must

be attached to the electrical power tool

and set in such a way that the smallest

possible area of the abrasive consum-

able is exposed to the operator. The disc

guard cover is there to protect the operator from

pieces breaking oﬀ and accidental contact with

the abrasive consumable.

c) Abrasive consumables must be used

only for their recommended purpos-

es, For example: never grind with the

side face of a cutting disc. Cutting discs

are intended for removing material using the

edge of the disc. Sideways forces on these

abrasive consumables can cause them to break.

d) Always use an undamaged mounting

flange of the correct size and shape

for your selected grinding disc. Suitable

ﬂanges support the grinding disc and reduce the

chance of it breaking. Flanges for cutting discs

are

diﬀerent from the ﬂanges for other abrasive discs.

e) Never use worn down abrasive con-

sumables intended for larger electrical

power tools. Abrasive consumables intended

for larger electrical power tools are not designed

for the faster rotational speeds of these smaller

electrical power tools and could break.

General safety advice for electrical power tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 75273 PMGS 12 B2 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 75273 PMGS 12 B2

Parkside IAN 75273 PMGS 12 B2 User Manual - French - 57 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 75273 PMGS 12 B2 Manual

Product: