744945
31
Zoom out
Zoom in
Previous page
1/34
Next page
31 GB
Preparations for use / Cleaning and care
Using the accessories (see Ill. D)
Air mattress adapter
6
, ball needle
12
Use a pipe wrench to unscrew the nozzle
9 a
of
the air blow gun
9
.
Then – depending on what is needed – screw
on the air mattress adapter
6
or the ball nee-
dle
12
, as well as the thread adapter
7
into
the barrel of the air blow gun
9
.
Universal valve connection
10
Screw the universal valve connection
10
directly
onto the compressed air hose
8
.
Cleaning and care
Thoroughly clean the spray stylus
3
immedi-
ately after use. Otherwise the paint can dry and
cause problems during the next use.
Thoroughly rinse out the spray stylus
3
with
water.
Use the thinner included to clean any stubborn
dried paint.
Note: The thinner is not suitable for water-so-
luble paints. Rather, it corresponds to a varnish
for thinning paints containing solvents.
Note: If you remove the paint nozzle of the
air blow gun
9
during cleaning, lubricate the
threads before reattaching it so its freedom of
movement is not affected.
Never lay the entire air blow gun
9
in a sol-
vent bath.
Note: If the air intake of the compressor should
become dirty, use a dry cloth to remove the ac-
cumulated dirt.
Fault Interrupted paint jet
or intermittent paint
delivery
Cause Solution
1. Paint almost
empty
1. Fill paint
2. Paint too viscous 2. Lower viscosity
3. Dry / defective
nozzle
3. Screw in nozzle tightly
or replace
Fault Interrupted paint jet
or intermittent paint
delivery
Cause Solution
4. Paint supply
restricted
4. Cleaning
5. Incorrect posi-
tion of spray
stylus
3
.
5. Correct position angle
Fault Spray pattern
incomplete
Cause Solution
1. Air head
dirty / defective
1. Clean / replace air head
1. Rinse with clear water
2. Nozzle dirty /
defective
2. Clean / replace air
nozzle
Fault Spray pattern irregu-
lar with drips
Cause Solution
1. Defective nozzle 1. Replace nozzle. Contact
a respective service centre.
2. Paint too viscous 2. Lower viscosity
3. Insufficient
working pres-
sure
3. Increase working pres-
sure (if necessary, not in-
cluded accessories, e.g.
pressure reducer)
3. Hose defective; replace
hose
Fault Non-uniform paint
amount delivered
Cause Solution
Nozzle dirty /
defective
Clean / replace air nozzle
Preparations for use
73868_par_Airbrush_Set_Content_LB1 (NL)+GB.indd 31 29.06.12 16:15
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 73868 PABK 60 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 73868 PABK 60 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 2,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 73868 PABK 60 A1

Parkside IAN 73868 PABK 60 A1 User Manual - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info