745066

Parkside IAN 73786 PDSS 310 A1 Manual

56
Zoom out
Zoom in
Previous page
1/59
Next page
56 GB
… / Environmental instructions and disposal information / Declaration of Conformity
Troubleshooting / Information about warranty and service processing
Information about warranty
and service processing
Creative Marketing Consulting GmbH
warranty
Dear customer, the warranty for this device is 3
years from the date of purchase. In the event of
product defects you have legal rights against the
retailer of this product. Your legal rights are not li-
mited in any way by our warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please keep the original sales receipt in a safe lo-
cation. This document is required as your proof of
purchase.
Should this device show any fault in materials or
manufacture within three years from the date of
purchase, we will repair or replace it - at our choice -
free of charge to you. Warranty services require
the defective device and the proof of purchase (sales
receipt) to be presented within the three-year period
along with a brief written description of the defect
and when it occurred.
If the defect is covered by our warranty, we will re-
turn the repaired device or replacement thereof. A
repair or exchange of the device does not extend a
new warranty period.
Scope of warranty
The device has been manufactured to strict quality
guidelines and meticulously examined before delivery.
The warranty applies to faults in material or manuf-
acture. This warranty does not apply to product
Faults Possible causes Action
Impact driver not
working
Trigger not pulled Pull trigger
No compressed air supply If applicable, drain condensation from tube (water
bag)
Straighten kinks in the hose
Connect compressed
2
air
Leak in compressed air
system
Remedy leak
Compressor defective Verify the compressor is supplying compressed air. If
necessary, have compressor repaired by a qualified
professional
Defect inside the air tool Have air tool repaired by a qualified professional
Not properly tight-
ening screw
Air pressure too low Increase air pressure.
ATTENTION! Never exceed the maximum ap-
proved operating pressure of the air tool!
Not loosening
screw
Torque is too low
Turn torque control
3
to a higher setting
Rusted screw Apply rust remover to screw
73786_par_Druckluft-Schlagschrauber PDSS 310 A1_content_LB2.indd 56 30.05.12 17:00
… 56 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 73786 PDSS 310 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 73786 PDSS 310 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info