744963
43
Zoom out
Zoom in
Previous page
1/46
Next page
43 GB
socket before you carry out any task
on the device.
DANGER OF INJURY! Always use the
angle grinder with the disc guard
cover in place. The disc guard cover must
be securely attached to the angle grinder. To
ensure the highest level of safety while using
the device, ensure that the smallest possible
area of the grinding or cutting tool is exposed
to the operator at all times. The disc guard cov-
er is there to protect the operator from pieces
breaking off and accidental contact with the
grinding or cutting tool.
DANGER OF INJURY! Ensure that the
guard
7
is attached so that its edge
is beyond the angle of the auxiliary
handle
6
(see Fig. B). Otherwise you
could injure yourself against the grinding or
cutting disc.
Open the clamping lever
8
.
Insert the disc cover guide
7
with the coded
projection
9
in the coded groove
16
.
Turn the disc guard cover
7
into the desired
position (working position). The closed side of
the disc guard cover
7
must always be facing
the operator.
Close the clamping lever
8
to firmly clamp
the disc guard cover
7
in place.
If necessary the clamping force of the connection
can be adjusted by tightening or loosening the
adjuster screw
10
.
Ensure that the disc guard cover
7
sits firmly
on the spindle collar.
Q
Attaching the auxiliary handle
CAUTION! For safety reasons this
device must always be used with the
auxiliary handle
6
in place. Otherwise
you could become injured.
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
Screw the auxiliary handle
6
on the left, right
or on the top of the head of the device.
Q
Attaching and replacing
roughing / grinding / cutting discs
Take note of the dimensions of the roughing /
grinding or cutting discs. The circular hole must fit
on to the mounting flange without play. Do not use
a reducer piece or adapter.
DANGER OF INJURY!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
Check the condition of the roughing /
grinding or cutting discs. They must be
free of damage, moisture or cracks.
Otherwise they could break up during use and
cause injury.
DANGER OF BURNS! Always wear
protective gloves when changing a
roughing / grinding or cutting disc.
Roughing / grinding and cutting discs become
hot during use. Do not touch them until after
they have cooled down.
NOTE: Always ensure the discs are free of dirt
before use.
Use only abrasive consumables or tools with
an allowable speed at least as high as the
no-load speed of the device.
DANGER OF INJURY! Press the spindle lock
button
11
only after the mounting spindle
14
has reached a standstill.
Press the spindle lock button
11
to block the drive.
Release the clamping nut
13
using the spanner
17
(see Fig. C).
Place the roughing / grinding or cutting disc on
to the mounting flange
15
with its labelled side
facing towards the device.
Then replace the clamping nut
13
, with its
raised side facing upwards, on to the mounting
spindle
14
.
Press the spindle lock button
11
to block the drive.
Tighten the clamping nut
13
again with the
spanner
17
.
NOTE: Replace a new disc immediately if it
runs unevenly or vibrates after being exchanged.
After replacing a disc let the device run under
no-load conditions for 30 seconds as a safety
check. Look out for unusual noises or generation
Preparing for use General safety advice for electrical power tools / Preparing for use
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 71830 PWS 230 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 71830 PWS 230 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 71830 PWS 230 A1

Parkside IAN 71830 PWS 230 A1 User Manual - French - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info