744954

Parkside IAN 71828 PET 25 A1 Manual

33
Zoom out
Zoom in
Previous page
1/37
Next page
33 GB
and advice. Electrical power tools are danger-
ous when they are used by inexperienced peo
ple.
e) Look after the device carefully. Check
that moving parts are working prop-
erly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have dam-
aged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this par-
ticular type of device. In doing this, take
into account the working conditions
and the task in hand. The use of electrical
power tools for purposes other than those in-
tended can lead to dangerous situations.
5. Service
a) Have your device repaired at the ser-
vice centre or by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
Safety advice relating
specifically to Electric
nailer / staplers
DANGER OF INJURY! Never
point the device at yourself or at oth-
er people or animals. Ensure that no
people or animals are on the other side of the
workpiece.
PROTECT YOUR EYES! Wear
protective glasses. This also applies
to people who may be helping with
the work by supporting or holding the workpiece.
Make sure the device is switched off before
you load the magazine. Set the ON / OFF
switch to position “0” and pull the mains plug
out of the mains socket!
Do not use the device to fix electrical cabling
in place.
Secure the workpiece. A workpiece held in a
clamp or vice is kept more securely in place
than one held by your hand.
Always work with the mains lead leading away
from the rear of the device.
DANGER OF INJURY! Use the device with
only the staples and nails specified above.
Ensure that the staples or nails do not project
from the surface of the workpiece or penetrate
through to the other side.
Short-term operation time: Let the device cool
down after 15 minutes of continuous operation.
DANGER OF INJURY! Keep your fingers and
other body parts away from the front plate
7
.
Never fire staples or nails through the air. At
short range the shot staples or nails could lead
to serious injury.
Only soft materials such as wood or textiles
should be joined using the device. Otherwise
the device could be damaged.
CAUTION! Connect the device to the mains
only when it is switched off. Set the ON / OFF
switch
2
to position “0”.
DANGER OF INJURY!
Switch the device on just before you intend to
use it. If you are not using the device, switch it
off to prevent unintentional firing.
Q
Before use
Q
Loading the magazine
Squeeze the end of the magazine slider
4
(see Fig. A).
Pull the magazine slider
4
out of the magazine
5
(see Fig. B).
Fill the magazine
5
with staples or nails
(see Fig. C).
Note on filling with nails: Use the right-
hand slot for filling with nails as shown in the
General safety advice for electrical power tools / Before useGeneral safety advice for electrical power tools
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 71828 PET 25 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 71828 PET 25 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info