744911
40
Zoom out
Zoom in
Previous page
1/55
Next page
40 GB/MT
Preparing for use
Q
Preparing for use
Q
Tensioning / changing
the sanding belt
RISK OF INJURY! Before
you carry out any work on the belt sander always
pull the plug out of the mains socket.
1. Then release the tensioner for the sanding belt
by moving the tensioning lever
9
fully out-
wards (see fig. A). The tensioner is now open
and the sanding belt can be removed.
2. Next insert a new sanding belt or change the
belt for one suitable for a different material or
one with a different grit size.
IMPORTANT: The direction of the arrows on
the inside of the sanding belt must agree with
that on sander housing.
3. Press the tensioning lever
9
back into its
initial position.
Adjusting the sanding belt:
Pick up the device, switch it on and turn it over.
Adjust the belt tracking by turning the adjuster
screw
6
until the edge of the sanding belt is
flush with and runs parallel to the edge of the
device (Fig. B.).
IMPORTANT: Always make sure that the
sanding belt does not cut into the housing.
Check the sanding belt regularly and if neces-
sary re-adjust it using the adjuster screw
6
.
Q
Advice on use
Light sanding pressure is enough:
Apply light sanding pressure only. The weight
of the belt sander alone is adequate to pro-
duce good sanding results. By adopting this
approach you will also prolong the life of your
sanding belts and obtain a smoother work-
piece surface.
Sanding and surfaces:
The sanding output and the quality of the surface
finish obtained are determined by the belt speed
and the grade of grit on the sanding belt (see the
section on “Selecting the correct rotational speed
and sanding belt”).
Sanding procedure:
With the sander switched on, bring it into con-
tact with the workpiece and move it forward
carefully. Work in parallel and overlapping
widths. Always work in the direction of the grain
to avoid undesirable transverse sanding marks.
After sanding always lift the device from the
workpiece before switching it off.
Q
Vacuum dust extraction
DANGER OF FIRE! There is
the danger of fire when working with electrical de-
vices that have a dustbox or can be connected to a
vacuum cleaner. Under certain conditions the
wood dust in the dust collection box (or in the vacu-
um‘s dust bag) may self-ignite, e.g. as a result of
flying sparks generated when abrading metals or
metal objects left in wood. This can happen partic-
ularly if the wood dust is mixed with paint residue
or other chemicals and the abraded particles are
hot from prolonged abrasion. Therefore you must
empty the device’s dust collection box and the vac-
uum cleaner’s dust bag before taking a break or
stopping work and always avoid overheating of the
abraded particles and the device.
Wear a dust mask!
Dust extraction using the dust
collection box:
Slide the dust collection box
10
on to the dust
extraction spout
5
on the side of the device
(Fig. C).
Emptying the dust collection box:
Pull the dust collection box
10
off the dust
extraction spout
5
. Open the dust collection
box
10
and empty it.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 68917 PBS 900 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 68917 PBS 900 A1 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 3,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 68917 PBS 900 A1

Parkside IAN 68917 PBS 900 A1 User Manual - German, Dutch, French, Italian - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info