744922
65
Zoom out
Zoom in
Previous page
1/85
Next page
63 GB/MT
Use / Use of accessories
and the working conditions and can be deter-
mined by means of a practical test.
The table below shows some recommended
settings (for guidance only and given without
liability) for a number of common applications.
The accessories mentioned may not all be sup-
plied as standard with the product. Sawing stone
is only permitted with the use of a cutting guide
(accessory).
Preselected rotation speed:
Material
Application
Tool Setting
Plastic,
varnish
Polishing Lambswool
bonnet
1
Fine finish
Felt polishing
disc
1
Metal Fine finish Buffing disc 1
Paint
removal
Sanding sheet 2-3
Wood,
metal
Brushing,
derusting
Cup brush,
sanding sheet
3
Metal,
stone
Grinding /
abrading
Grinding disc 4-6
Metal Roughing /
grinding
Roughing /
grinding disk
6
Stone Cutting Cutting disc
and cutting
guide
6
Changing a disc
Always wear protective gloves
when changing cutting or roughing /
grinding discs.
Press the spindle lock button
9
only after the
mounting spindle
7
has reached a standstill,
Fig. A.
Press the spindle lock button
9
to block the
drive.
Release the clamping nut
6
using the spanner
11
, Fig. B.
Place the roughing, grinding or cutting disc on
to the mounting flange
8
with its labelled side
facing towards the device.
Then replace the clamping nut
6
, with its
raised side facing upwards, on to the mounting
spindle
7
.
Press the spindle lock button
9
to block the
drive.
Tighten the clamping nut
6
again with the
spanner
11
.
Note: Replace a new disc immediately if it runs
unevenly or vibrates after being exchanged.
After replacing a disc let the device run under
no load for 30 seconds as a safety check.
Look out for unusual noises or generation of
sparks.
Check that all the fastenings are correctly
attached.
Pay attention to see that the arrow showing the
direction of rotation on the cutting or roughing /
grinding discs (including diamond cutting discs)
corresponds with the direction of rotation of the
device (see arrow on the head of the device).
Use of accessories
Cutting / roughing discs
You can use the following cutting or roughing/
grinding discs with this device:
Dimensions: ø 125 x 22,2 mm
to max. 6 mm thick
(depressed centre)
Speed: min. 12000 rpm
Circumferential speed: 80 m / sec
ø 125 x 22.2 mm
to max. 6 mm thick
(depressed centre)
12000 rpm
80 m / sec
Flap discs for metal
Dimensions: ø 125 mm
Speed: min. 12000 rpm
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 67037 PWS 125 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 67037 PWS 125 A1 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 3,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 67037 PWS 125 A1

Parkside IAN 67037 PWS 125 A1 User Manual - German, Dutch, French, Italian - 71 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info