744922
62
Zoom out
Zoom in
Previous page
1/85
Next page
60 GB/MT
General safety advice for electrical power tools
The workpiece must be supported to both sides
of the cutting disc and particularly near the
cutting disc and at the workpiece edge.
f) B
e particularly careful when pocket
cutting in existing walls or other areas
where you cannot see what you are cut-
t
ing into. The cutting disc plunged into the surface
could cut through gas or water pipes, electricity
cables or other objects and cause kickback.
Special safety advice for
abrading using sandpaper
Do not use over-sized sanding sheets.
Follow the manufacturer’s recommen-
dations for sanding sheet size. Sanding
sheets that project beyond the backing pad
could cause injury in addition to jamming,
tearing of the sheet or kickback.
Special safety
advice for polishing
Do not use the polishing bonnet if it
has any loose parts, in particular the
fastening cords. Tuck the fastening cords
away or trim them. Loose fastening cords rotat-
ing with the attachment could catch your fingers
or become trapped in the workpiece.
Special safety advice for
working with wire brushes
a) Bear in mind that wire brushes lose
pieces of wire during normal use. Do
not overload the wires by applying too
much pressure. Flying pieces of wire can very
easily penetrate thin clothing and / or skin.
b) U
se a guard, if recommended, but m
ake
sure that the wire brush does not come
into contact with the guard. The diameters
of disc brushes and cup brushes can increase
due to contact pressure and centripetal forces.
Safety advice
for angle grinders
DANGER OF ELECTRIC SHOCK! Do not
operate the device if the mains lead
or mains plug is damaged.
DANGER OF ELECTRIC SHOCK! Do not
touch the mains lead if it becomes
damaged or cut through while you
are using the device. Pull the plug out of
the mains socket immediately and have the de-
vice repaired by a suitably qualified person or
at your service centre.
DANGER OF ELECTRIC SHOCK! Do not
operate the device if it is damp and
do not use it in a damp environment.
DANGER OF ELECTRIC SHOCK! If you
use the device outdoors, always con
nect
it through a residual current device
(RCD) with a maximum trip current of
30 mA. If using an extension lead, always use
one that is approved for outdoor use.
Do not suspend or carry the device by
the mains lead. Always work with the
mains lead leading away from the
rear of the device. Otherwise the device
could be damaged.
Grinding discs must be carefully kept
and handled in accordance with the
manufacturer’s instructions. Otherwise
they could be damaged.
Make sure that abrasive consumables
and tools are attached in accordance
with the manufacturer’s instructions
and advice. Otherwise they could become
detached from the device and result in injury
and / or damage to property.
Ensure that any spacers supplied and
required for the use of certain abrasive
consumables and tools are installed.
Do not use separate reducing bushes
or adapters in order to make grinding
discs with a larger bore fit.
When using abrasive consumables
and tools with a threaded insert make
sure that the tread is long enough for
the spindle length. Otherwise the grinding
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 67037 PWS 125 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 67037 PWS 125 A1 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 3,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 67037 PWS 125 A1

Parkside IAN 67037 PWS 125 A1 User Manual - German, Dutch, French, Italian - 71 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info