744906
56
Zoom out
Zoom in
Previous page
1/75
Next page
56 GB/MT
J Always keep the device
clean, dry and free of oil or grease.
J Children or persons who lack the knowledge or
experience to use the device or whose physical,
sensory or intellectual capacities are limited
must never be allowed to use the device without
supervision or instruction by a person responsi-
ble for their safety. Children must never be
allowed to play with the device.
Q
Operation
Never use the device for a purpose for which it was
not intended or with non-original parts / accessories.
The use of tools or accessories other than those rec-
ommended in the operating instructions could lead
to you suffering an injury.
Q
Charging the battery pack
NOTE! A battery pack that has been
unused for a while or never been charged
must be charged before reuse or first use.
The battery pack requires about 3-5 cycles before
it can reach its full charge. The charging process
takes about 180 minutes.
CAUTION! RISK OF INJURY!
Always pull
out the mains plug (
mains adapter
10
) before
you
insert the battery pack into or take it out of
the charger.
j Connect the adapter
10
to a mains socket.
j Insert the battery pack
3 a
into the charging
cradle
9
. This can only be inserted with the
correct polarity.
j The LED
11
lights up green whenever the bat-
tery pack
3 a
is in the charging cradle
9
and
the adapter
10
is connected to a mains socket.
CAUTION! Do not charge a battery pack for
a second time in close succession. There is a
danger of overcharging the battery pack.
Q
Inserting / removing the
battery pack into / out of the
drill / grinder
Inserting the battery pack:
j Set the ON / OFF switch
5
to position “0”.
j Insert the battery pack
3 a
into the drill / grinder
until it engages.
Removing the battery pack:
j Pressing the battery pack buttons
3
at the
sides at the same time allows you to remove
the battery pack
3 a
.
Q
Reading off the battery status
The status or residual power is indicated as follows
in the battery-operated LED
2
whenever the appli-
ance is switched on:
RED / ORANGE / GREEN = maximum charge / power
RED / ORANGE = medium-level charge / power
RED = weak charge recharge battery
Q
Inserting or replacing
a tool / collet
j Press the spindle lock
8
and keep it pressed.
j Rotate the clamping nut
6
until the lock
engages.
j Loosen the clamping nut
6
with the combina-
tion key
23
.
j If a tool is already inserted, remove it.
j First insert the tool you wish to use through the
clamping nut
6
before you insert it into the
collet
18
suitable for the tool shaft.
j Press the spindle lock
8
and keep it pressed.
j Insert the collet
18
into the threaded insert and
tighten the clamping nut
6
on the thread using
the combination key
23
.
NOTE: Use the screwdriver end of the combi-
nation key
23
to release or tighten the screw of
the mandrels
13
.
General safety advice for electrical power tools / Operation
56052_par_Akku-Multischleifmaschine PFBS 9.6 A1_content_LB5.indd 56 21.04.11 13:22
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 56052 PFBS 9.6 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 56052 PFBS 9.6 A1 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 4,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 56052 PFBS 9.6 A1

Parkside IAN 56052 PFBS 9.6 A1 User Manual - German, Dutch, French, Italian - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info