Manual Parkside IAN 55732 PESG 120 A1 (page 30 of 34) (French)

745193

Zoom out

Zoom in

1/34

30 GB

Never use the welding shield without protective

glass, as the optics can otherwise be damaged.

Replace the protective glass early to ensure

good visibility and fatigue-proof working.

Tight and moist spaces

When working in tight, moist or hot spaces, use

insulating pads and intermediate layers in ad-

dition to gauntlet gloves made from leather or

other insulating materials to insulate the body

from earth.

When using welding equipment in electrically

dangerous conditions, e.g. in tight spaces from

conductive walls (kettles, pipes, etc.), in wet

spaces (soaking of work clothes), the output

voltages of the welding equipment may not be

higher than 48 Volts (rms value) in open loop.

Based on the output voltage this welding

equipment may be used in these conditions.

Protective clothing

Whilst working the welder must be protected

against rays and burns all over the body with

the appropriate clothing and face protection.

Remember the following steps:

- Put on protective clothing before welding.

- Put on gloves.

- Open windows or vent to ensure air supply.

- Wear safety goggles and a mask.

Wear gauntlet gloves made from suitable ma-

terial (leather) on both hands. These must be in

good condition.

Wear suitable aprons to protect the clothing

from sparks and burns. When required based

on the working method, e.g. welding overhead,

wear a protective suit and, if necessary, a head

guard.

Protecting against

rays and burns

Mark the work area with a sign „Danger! Do

not look into ﬂames!“ to indicate the risk to the

eyes. If possible, shield the work areas to protect

persons nearby. Keep unauthorised persons

away from the welding area.

Walls in the direct vicinity of ﬁxed work areas

should be neither light coloured nor glossy.

Protect windows against rays passing through

or reﬂecting at a minimum to head height, e.g.

with suitable paint.

Assembling the welding shield

Attach the handle

to the welding shield

as shown in Fig. B.

Install the protective glass

to the welding

shield

as shown in Fig. B.

Preparing to weld

Note: When activating the power verify the

current indicator moves and the lead screw is not

jammed.

Note: Verify the retaining screw on the electrode

holder

and the earth terminal

are secured

before every use If necessary, tighten with a cross-

tip screwdriver.

Note: If the tensioning force of the electrode

holder

and the earth terminal

subsides,

replace immediately.

Connect the electric cables.

Set the ON/OFF switch

to the „ON“ posi-

tion. The current indicator will light up when

operation starts.

To end operation, set the ON/OFF switch

to the auf „OFF“ position.

Note: The yellow indicator light

lighting

up indicates overheating. The electric circuit will

automatically be broken. Operation will end.

Attach the earth terminal

directly to the

work piece or to the pad on which the work

piece is placed.

Note: Ensure direct contact to the work piece.

Thus avoid painted surfaces and/or insulation.

Note: Always use the welding shield

whilst welding. It protects the eyes from the

Preparing to weld / Welding / Overheat protection / Maintenance

Safety information / Assembling the welding shield / Preparing to weld

55732_Elektro-Schweissgeraet_content_FR.indd 30 18.12.13 07:12

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 55732 PESG 120 A1 in the language / languages: French as an attachment in your email.

The manual is 1,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 55732 PESG 120 A1

Parkside IAN 55732 PESG 120 A1 User Manual - English, German, Dutch - 34 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 55732 PESG 120 A1 Manual

Product: