745204

Parkside IAN 55730 PSE 2800 A1 Manual

29
Zoom out
Zoom in
Previous page
1/34
Next page
29 GB
Safety instructions / Before use … / … / Cleaning, maintenance, storage, transport and ordering replacement parts
connector
4
of the generator (fig. C / Pos. 4)
and from the other side to an external ground.
Operation
ATTENTION! When being used for the first
time, motor oil (15 W-40, approx. 0.6 l) and petrol
(unleaded normal petrol) must be put in.
Check the fuel level and the oil, and if necessary
top them up.
Make sure you have adequate ventilation.
Ensure that the spark cable is securely in the
spark plug.
Unplug any electric device connected to the
generator.
Start the engine
ATTENTION! When starting with the express
start
13
you can injure your hand with the sudden
kick back.
Wear protective gloves when starting.
Open the petrol tap
14
by turning the tap down-
wards.
Put the on / off switch
11
to the on position.
Turn the choke lever
12
to I Ø I (in the left
position).
Start the engine with the express start
13
by
sharply pulling the handle. If the engine has not
started pull the handle again.
Push the choke lever
12
back once the engine
has started (in the right position).
To load the generator
Connect the device to the 230 V∼ socket
3
.
ATTENTION! This socket can be loaded con-
tinuously (S1) with 2600 W and short term (S2) for
a maximum of 2 minutes with 2800 W.
Note: Some electric devices (sabre saws, drills etc.)
can use more electricity when doing heavy duty tasks.
Storing the engine
Before putting away, let the generator run with-
out load so that the device can „cool down“.
Turn the on / off switch
11
to the „OFF“ position.
Close the petrol tap
14
.
Overload protection
2 x 230 V sockets
WARNING! This generator is fitted
with an overload protector.
This cuts off the sockets
3
. By activating the over-
load switch
6
the sockets
3
can be used again.
ATTENTION! If this happens reduce the
amount of electrical output which you are
extracting from the generator or remove
defective devices which are attached.
ATTENTION! Faulty overload switches
should only be replaced with identically
constructed overload switches with the
same performance data. Please use our
customer service department.
Cleaning, maintenance,
storage, transport and
ordering replacement parts
Before cleaning and maintenance work, turn off the
engine and pull the spark plug connector
29
out of
the spark plug
28
.
ATTENTION! Turn the device off imme-
diately and contact your Service Station:
- With unusual vibrations or noises.
- If the engine seems overloaded or has backfired.
Cleaning
Keep the safeguards, air vents (fig. B / Pos. B1)
and the engine housing as dust and dirt free as
possible. Wipe the device with a clean cloth or
blow it with compressed air with low pressure.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 55730 PSE 2800 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 55730 PSE 2800 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 55730 PSE 2800 A1

Parkside IAN 55730 PSE 2800 A1 User Manual - French, Italian - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info